KBRS22KGBL0 KitchenAid Refrigerator - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

remove parts that were not need installed water valve , ice maker unit and hooked up water supply tested and it works fine. got the parts really quick Thank You

Very simple fix, remove 3 screws, two connectors to the old switch

Remove 3 screws, took top hinge out, fz door and inserted shim...done.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.

I took the cover off of the evaperator in the back of the freezer compartment and thawed the ice out with a heat gun. I then replaced the bimetal defrost timer I did have to change one connection as it would not plug into the harness.
I found the Defrost timer in the front of the refrigerator behind the filter cover at the bottom. Just one screw and a quick plug in and everything is working wonderfully. no more icing up

first I took the inside freezer panel off. Pulled off the deformed gasket. I noted how it was attached to the door. I then took the new gasket and placed it on the panel and reattached the panel to the freezer door. The screws are small and can get easily misplaced. Use a recepticle to hold the screws, it does make the job much easier. I also used a power drill which made the job move along nicely. Easy as pie. Thanks. I know where to get my parts in the future.

I removed the ice maker with 3 screws after having shut off the water. I tried getting the part locally but thought it was a bit much. Of course after having had ordered the wrong part, PS51041 and having it over nighted here and paying the return shipping I would have saved money getting it locally. When I finally got the right part I used the power cable and level lever off the old maker and reinstalled the ice maker in just a few minutes with a nut driver and screwdriver. Thurning on the water in about and hour it started making ice. When ordering online make sure you can get a large enough diagram to see what you are getting. If you can't ,call their phone number ant talk to a live person.

Followed the video instruction and it was fairly easy to install. Let the gaskets sit for a day to reshape itself. Started by loosening the screws then removal of the gasket was done. The only hard part was to align the Gasket evenly. Not removing the doors made the install a little more difficult for alignment.

Most difficult part was finding where they hid the defrost timer. (it is in the left front under the fridge behind the kick panel.) just unscrew the two fastener screws from the front, tilt fridge up on one side, slide timer bracket back and remove. Unplug and remove timer from metal bracket. Replace timer and remount bracket.

Emptied unit and removed screws holding panels at rear of freezer compartment. Removed panels. Removed two screws holding motor. Made diagram of wire locations and fan blade orientation. Removed three wires and fan blade from motor. Took new motor and installed wires and fan blade to motor. Installed motor with screws. Test ran frig and reinstalled panels.

Removed panel and motor cover at rear of freezer compartment. This requires 1/4" nut driver. Removed motor assembly bracket and wiring, careful to note where ground, neutral and hot were attached. The entire assembly must be removed from the freezer compartment in order to swap new motor for old motor. Re-inserted assembly into freezer compartment, reattached wiring. Made sure all assembly screws were tightly fastened and wiring was correct. Re-attached panel cover and motor cover. I did note that a few of the 1/4" machine screws wobbled in the original holes; I used slightly larger, 5/16" head machine screws of identical length as replacements. New motor is much quieter. No longer sounds like a truck is idling in our home.