KDDC24CVX01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from Norcross, GA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Won't make ice cubes.
Removed bottem screw and loosened two top screws. Removed icemaker from support screws and disengaged cable. Replaced in reverse order. Total time was about 15 minutes.
Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.
. . . thanks!
Great DIY experience. Ordering the part was easy and delivery was very fast. Simple installation and had my first cubes in apprximately 15 minutes.
. . . thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Valley Village, CA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Camas, WA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.
Simply removed the old and replaced with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Las Vegas, NV
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Leaking tray shorted heater
Removed the old ice maker and replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Clifton, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Replace Leaky Ice maker
Removing the hex screws from the existing unit was trouble until I found the screwdriver attachment to the hex wrench. The MOLEX type power connector was an exact match for what was on the unit, so the conversion cables were not needed. Unit worked fine. No more leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from Metairie, LA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old ice maker was leaking water during initial fill cycle
Removed three srews holding the ice maker in place. Unplugged the wiring. Plugged in new ice maker wiring. Installed the new ice maker with the three screws. I left the old wiring in place. Works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Rockford, IL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice maker would not stop making ice.
I viewed the video that was provided on partselect.com. The video was very instrumental in the removal and installation of the ice maker. I removed the old ice maker and installed the new ice marker, turn the water valve back on and had ice within 24 hours. When I reconnected the electrics and turned the water supply back on to the ice maker I thought it would fill with water right away, but it didn't. So I determined that the ice maker needed to run though a cycle, which took several hours, before it actually started making ice. With the video I was able to change the ice maker in less than a half an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Antioch, IL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water leaking out of Icemaker
I undid two top screws and one bottom screw. The tools came out of my cheapo walmart tool kit. I disconnected the power connector. I then put the new Icemaker in and waited for ICE. 12 hours later still no ice. I contacted Parts Select and before I knew it an new Icemaker was ordered and delivered to my doorstep. I received several emails to confirm the refund and re-billing of icemaker. I was absolutly astonished by how well they responded. I figured weeks after the first replacement came in DOA but two days later I had Ice and all was well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lev from Fanwood, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Plastic coating chiping-off
First I removed one screw that hold the element in place, lifted element about half an inch. I then pulled the element out about 2-3 inches and disconnected the wire. Then replaced two clips on top of element and re-connected the wire, put screw back and VUALYA....done!!!!!!!!!!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mathew from cleveland hts., OH
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
would not make ice
remove the ice bucket support bracket and remove bottom screw from icemaker, loosing the two top screws and slide icemaker back enoughto unplug electric harness
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- wilfried from LAKESIDE, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Could not get the replacement Ice Maker back on the top brackets...
Removal was easy...Removing and installing arm was a bit difficult...Called a service man to install...He also had a bit of difficulty, but had it done in less than 45 minutes... He mentioned that my brackets had a different set up than most...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Bordentown, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Wrench set
leaky ice maker to no ice at all
Parts arrived amazingly fast. Replaced top ice maker and bottom water control valve[which was probably the source of my problem all along] in about an hour. The online installation video's were a big help. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Parker from Bangor, ME
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker unit leaked
followed instructions and replaced unit.
very easy and will roder again from this
very easy and will roder again from this
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- greg from shalimar, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
replaced ice maker
three screws and a plug in and it was done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Dennisville, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
ice maker kept filling tray, dld not empty
replaced the element as described. it worked for 2 cycles and flooded the capture tray. I thought it may be an issue with the water supply line so I replace it and insured it was getting a good feed.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.
I have now shut the unit down and restating it . thank you for your concern. Any tips would be appreciated.
Was this instruction helpful to you?
Thank you for voting!