KFIS20XVWH7 KitchenAid Refrigerator - Instructions

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

YouTube helped ,diagnosed problem ,found defective part removed and replaced with new part.
Is a little job on your knees

My wife snapped the part in place in 2 seconds.

first of all,i just want to thank parts select for sending me a second ice maker at no charge.after installing the first one and it didn't work,i talked with Heather and she sent me a new one.installation went the same as before.hardest part is getting the quick connect wire harness apart and the ice fill arm .it is working great and my home is happy.thank you!

I easily ordered the part. When it came in, I just shut off the water, disconnected the electricity, and followed instructions to remove shelving and drawers. Then removed the rear interior cover, removed the old water inlet valve and installed the new one. Just a couple moldex wire connections and the 3 water lines in and out. Don't know if this is still ok, but so simple a caveman could do it. Sorry Geico.

Looked online for instructions. I had to remove the shelves from inside the frig, then pop off part of the right inside back wall. The way the 3 water lines attached to the inlet valve was a terrible design. There are plastic little collars that need to be pushed back to release the water lines from the old valve, then when you install the new valve, you need to push them back to reattach the water lines. Once installed, one had a leak. No matter how hard I tried I couldn't get the little plastic collar to disengage. I couldn't push the line in further and I couldn't get it back out. Ended up cutting the line off at the valve just to get it out. Then had to cut out the piece that was still stuck in the valve. Tried to install it again and it leaked even more. Ended up putting the old valve back in and throwing away the $130 new inlet valve because there are no returns on electrical parts. Total waste of time and money ! ! ! Not happy to say the least.

Let the ice in the freezer melt while installing P trap drain tube

Replaced water/ice maker inlet valve from video instructions from Just Answer. The inlet tube for the water dispenser would not cede in the valve and this created a leak problem from the water dispenser connection. Called repair tech and he could not get the line to cede correctly in the inlet valve. Am going to request a replacement part. This has been very frustrating!

I brought you the exploded view of the crisper parts on your website and proceeded accordingly. Besides the three nuts holding the end cap to the frig interior wall the temperature adjustment linkage had to be disassembled on reassemblied on the new replacement end cap. Plastic linkage parts present the problem of breakage, so one must be careful during the disassembly process. Some other type of fasteners for the linkage assembly (screw and nut, ball and socket) would be prefereable. All and all, its a machine. Wtith exploded view, what could go wrong?

Removed the whole ice maker unplug one wire harness replaced ice tray with new one.
Very simple.

Replaced two original crisper drawers with 2 new drawers; replaced broken end cap which required the removal of a few bolts and screws. The replacement parts were identical matches--a huge relief. The interior of the fridge looks like new. This follows upon not being able to get the parts directly from the manufacturer.

I had to replace the entire door because the plastic tabs holding the window in place snapped off. I just opened the door to see how it was held in place, released the old door and installed the new one. Job complete in less than a minute.

I unpacked the glass and slipped it into the shelf. Done.
What was more impressive was the delivery time. I ordered the glass at about 12:30pm one day and the glass was at my door by 9am the next morning. Even my husband was impressed with that.

Removed old ice maker. Unscrewed unit from slide. Unplugged old wire. Screwed on new unit. Replugged in wire. Slid ice maker back into refrigerator and all worked properly.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.