KBFS25EWMS10 KitchenAid Refrigerator - Instructions

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Loosen the top 2 screws, remove the bottom screw, unplug the wire harness, lift up the ice maker and remove. To install the new one simply reverse the removal procedure.
Note: You may want to wipe the inside of the new one to remove the protective grease or discard the first 2 cycles of ice.

repair was extremely easy.
Whether it was magnets weakened or seal getting stiff with age not allowing it to seal well, these gaskets improved it. Still not as strong a magnetic pull as it could be though. I will also say that the seals didn't pull tight at first. It seems the seals needed to flatten a bit before the magnets did their job.

I removed and disassembled the broken frame. I cut a six inch piece of coat hanger and folded in half and crimped together. Then I took pliers and made a hook that I hooked into the metal strip in the back of the refrigerator that holds the upper shelves. After replacing the frame, center rail and glass I bent the wire up under the back of the frame to provide a support. The back of the frame is weak and has no center support.

Talking with the service tech and youtube video it was a snap... Saved a service repair and a 25% parts mark up..

Don't try and remove the front/handle from the broken pan, you will break it and its double the price of the pan, just use the small hammer to break the pan into smaller pieces and remove handle from them then the handle will just snap onto the new pan. Piece of cake!

It was easier than I had anticipated. Just had to make sure that I was very careful in removing the old part so I did not break any of the good plastic that I needed in order to install the plastic temperature control to the new part.

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

First I removed the pantry drawer; then the two crisper drawers and glass shelf. Then I removed the hex screws that held end cap in place. Removal of cap from refrigerator was complicated by the adjustable temperature control - it is loosely attached at the back of end cap and also has to be removed to get cap out. Gentle persuasion accomplishes this. Getting the slider off end cap also a bit difficult. Then I removed the drawer glides. Reversing all steps was fairly easy and the rest of the "fix" went well. I wished that there had been some written directions - or at the very least, a diagram of how all went together. All in all was still cheaper than repair person.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

Easily pulled out the gaskets off the refrigerator doors and replaced them with the new ones. The installation video was also a big help in the process.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!