KFIS25XVMS10 KitchenAid Refrigerator - Instructions

Saw U tube instrctions how to install and it was easy

Simple placement of new glass pane into crisper top

Removed the food bins and lower shelf. Unscrewed the end cap. Removed the drawer hinge. Re-installed hing on new end cap. Installed the new end cap. Re-installed drawers and shelf. DONE!

Great graphics on the website helped to correctly idenitfy the required part. Part arrived quickly and well packed. One of the easiest transactions ever!

Center Rail:
Removed the crisper drawers. Removed contents and the glass shelf above the the crisper drawers. Positioned the center rail as shown in the diagram, but it was not an easy fit so afraid it might get broken by forcing it, rolled the front edge of the glass shelf support slightly outward which enabled the rear tab of the rail room to engage into the rear shelf bracket and the "front tab" of the rail to slip into the notch at the front edge of the glass shelf support.

Pantry Drawer and Lid:
Lid was already long gone so I just slid the cracked pantry drawer out of the refrigerator, cleaned the surface under the drawer, placed the new drawer on the slides and in it went. The drawer lid was another finesse it in without breaking the hinge tab so had to position it slightly on the diagonal and popped it into place.

Now the crisper drawers glide silently and effortlessly along the side rails with the new center rail in place while the deli drawer lid raises itself automatically with a gentle grasp of the drawer pull.

It had been so long since those parts had busted I had forgotten how the assembly was supposed to work. It's like having a new refrigerator.

Now if I could just manage the ice maker!

Once the part arrived, which was very quickly BTW..all I had to do was remove the old filter and then just screw the new one into place....Now I just happen to be both female and blonde but was able to get the job done in less than 15 minutes (that includes opening the box) and with very little water dripping from the old filter!!! Looks like I could work as the Maytag repair woman soon!!

I had to replace the entire door because the plastic tabs holding the window in place snapped off. I just opened the door to see how it was held in place, released the old door and installed the new one. Job complete in less than a minute.

You remove the white frame from around the old pan by popping it off from the bottom being careful not to break it. Install it on the new pan using the reverse procedures. Popping it on starting at the bottom. Very easy

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

The old plactic ring can be removed with flat bladed screw driver, starting on the right side prying it up worked best for me. The new seal snaps in only one way take your time to get it wright.

Removed old gasket and installed the new one. Used a hairdryer to smooth out the edges.

Removed two screws on outer face plate and set aside the face plate after disconnecting from power supply. Remove dispenser paddle which had broken and replaced with new part. Reattached power connections and reattached the face plate. Relatively easy process.

took out the drawers and glass shelf and unscrewed the sides took parts for drawer glide off put them on the new part reinstallled saved $110 service cll and $20 on the part!