KBFS22EWMS5 KitchenAid Refrigerator - Instructions

First, I removed the old door gasket by pulling it out of the channel it was mounted in, noting the orientation of the gasket. Then, it was a simple matter of lining the new gasket up with the channel and pressing it into the groove. Very easy repair, and the door seals great!

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Shut down refrigerator at the breaker. Placed freezer items in a cooler. Removed top shelf. You must release roller covers on each side to remove the shelf ( Two front screws must be removed) Took off freezer door. (4 screws holding the door to the bracket) Disconnected ice maker electronic plug. Totally removed bottom screw holding ice maker. Loosen two top screws and remove ice maker. Reverse process to install.

Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.

Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.

This was a very easy repair job! I just needed to remove the drawers and shelving, put the new ladder hook on, and repace the shelving and drawers. It took longer to remove the items from the fridge, then it did to replace the ladder hook.

I removed the glass top and then rail and frame.
I had to remove the gaskets from the old frame and put them on the new one.
The steel support and the slide mechanisms were difficult to remove. I needed a screwdriver to do this.
Some directions would have helped here.
It was easier to snap them back into the new frame.
I set the frame and then rail back into the refrigerator,
replaced the glass.

Turned old one until it snapped out. Replaced it with a turn.

Removed the drawers and shelf unit above the shelves. Installed the new rail and put the shelf unit and drawers back in. Less than 5 minute repair. Very fast delivery of part and reasonable pricing.

Turn water and refrigerator off, use hair to thaw the ice maker filler tube, then remove the filler tube inside the freezer. Next remove the water supply line cover plate in back of the refrigerator. Now remove the speed clip at the white pvc elbow and pull out the supply line. Next, grasp the pvc elbow with pliers and pull hard to remove. The new filler tube is a 1 piece design (filler tube and elbow combined) and needs to be cut to the proper length. Mark it inside the freezer, remove it and cut to length. Now coat the outside flange with caulk or PU glue and snap into the opening. Put the speed clip on the elbow first and center it. Ensure that the spreader insert is in place in the plastic tube, then slide the supply line into the elbow untill completely engaged. Replace cover.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First and foremost shut off the water supply to the Ice maker. Some recommend unplugging the refrigerator or disabling the circuit breaker to the refrigerator. Then after emptying the freezer remove the freezer door by loosening the four hex head screws and lift the door straight up and set it off to the side.You can then remove the lower basket. Now locate the clamps located at the rear sides of the inner basket and use a small flat blade screwdriver to gently push the tabs toward the outside of the side clamps while pulling up at the same time and releasing the clamp. Now repeat this procedure on the opposite side of the inner basket. The inner basket can then be pulled out being careful to not damage the roller tracts or gear rollers. Three hexhead screws secure the ice maker to the wall. The screw under the ice maker must be removed while the two on top just loosened. The electrical plug is removed by depressing the tabs on the top and bottom of the plug and then pulling outward. Carefully lift the ice maker upward and out from the two upper hex head screws. You can then install the replacement icemaker by reversing the procedure.

changed the starter connected to the compressor

Took drawers out, inserted the rail and put the drawers back in and voila. Fixed.

Turned the old one to unseat and replaced with a new one in the reverse order.