KSSC42FTS16 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dennis from Lawrenceville, GA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Light switch which turns on the lights when the door opens went out
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene from Whitehall, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No light in frig
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kory from Seattle, WA
- Parts Used:
- WP2266802
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Lost power
It was simple using PartSelect to locate the likely source of the problem. Also the pictures of the part helps confirm that you have the correct item.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Big Flats, NY
- Parts Used:
- WPW10190929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replaced ice model
Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Norma from Unionville, MO
- Parts Used:
- WPA3073101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Needed a new bulb under the microwave.
After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugine from San Antonio, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Water Filter
Peice of pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ann from gastonia, NC
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
time for filter change
Tried to remove filter with no success, there were no instructions in the package. "googled" how to install whirlpool filter and found how to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Raleigh, NC
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed to be replaced
Pulled out the old filter with the push of a button, removed filter cover from frig, took covers off the end of new filter and pushed it into the slot replaced cover. Job done--1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Josh from English, IN
- Parts Used:
- W11578915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
evaporator fan motor out
I got the part....I put it in. That's about it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Boynton Beach, FL
- Parts Used:
- WP2188820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer temperature too cold
Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from The Villages, FL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacement
The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dora from Rock Island, IL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light would come on and off
Viewed the viedo - it showed what to do
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Spring, TX
- Parts Used:
- WPW10190929
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Ice mold was leaking causing all the ice to freeze into one chunk.
Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.
Was this instruction helpful to you?
Thank you for voting!