KBLO36FTX06 KitchenAid Refrigerator - Instructions

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

It was simple using PartSelect to locate the likely source of the problem. Also the pictures of the part helps confirm that you have the correct item.

Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

Peice of pie

Tried to remove filter with no success, there were no instructions in the package. "googled" how to install whirlpool filter and found how to do it.

Pulled out the old filter with the push of a button, removed filter cover from frig, took covers off the end of new filter and pushed it into the slot replaced cover. Job done--1 minute.

I got the part....I put it in. That's about it.

Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.

The noise seemed to be coming from the closing cam at the top of the door, so we figured it had worn over time and was no longer operating smoothly, but rather popping into place when the door was opened all the way. We ordered a new cam, which was about $20 for a quarter-sized piece of metal with two holes in it. Expensive for what it was, but cheaper than calling a repair person for sure. Our first problem was how to disengage the spring that closes the door. It was hard to get a purchase while standing on a stool and the tension on the spring was very tight. Finally my husband rigged up a sort of pulley system to get more leverage and was able to get the spring off. The next problem was removing the screw that held the cam assembly in place. We were afraid we were going to have to saw it off, but finally my husband was able to remove it and it was barely salvageable to reuse with the new cam. After that, reassembling the system with the new part and reattaching the spring was relatively straight forward. The good news is, no more annoying popping sound!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Did you know you have to press the button next to the filter before you pull on the filter cap? Like most week end warriors, I just pulled the cap and of course, I broke it! The repair was simple, hopefully, in six months I will remember to press the button!

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!