KSC24C8EYP02 KitchenAid Refrigerator - Instructions

Took the old one out and put the new one in

Popped out the old switch and replaced it with the one dying

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

The part was perfect, easy installing. The customer service representative was knowledgeable and very helpful.

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.

Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

I went onto YouTube to see how to properly replace the old gasket with a new one. The new gasket was softer and had a better upgraded seal design. Installation required me to CAREFULLY use the putty knife to push the gasket into the holding slot. This is also a better. more secure design. The corners of the hard plastic insert did need to be SLIGHTLY trimmed to eliminate some "over gap closeness". I did the work with food in the refrigerator. I suggest that you do an EXTENSIVE defrosting as ice will have probably built-up way beyond "normal" using the old gasket. I defrosted several days after installing the new gasket. I used a hair dryer, spent about a 1/2 hour from top to bottom and drained about 6-8 oz. of "Frost". I also only fill the fridge with food about 3/4 full. This provides proper air circulation and even cooling. I hope you found this helpful.

with vidio

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

I use a Screw drive a Nutdriver set Needlenose Pliers and it took 30mins to fix.

We thought the trim piece would pop off the drawer, but instead the trim is glued to the drawer handle. After puzzling over what to do for a couple minutes, we grabbed some pliers and SLOWLY leveraged / peeled the old trim off and put the new trim on.

Go slow. Bend the old trim as you peel it off and use the pliers as a lever. Do a little at a time.

I took off the broken tube and attempted to order a new one with the confusing we sight at parts.com- after 3 attempts I finally got the right part with help from the operator at parts . Com( nice and helpful) but had to ship wrong parts ( the 2 wrong ones) back. The parts were of good quality and we're not hard to put on