KBRS19KTMS2 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Nicole from BUFFALO, NY
- Parts Used:
- WPW10284685, WPW10284684, W11658402
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The freezer door wouldn't stay closed
Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Pompton Lakes, NJ
- Parts Used:
- WP67001716
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Broke shelf holder hook
This is the small part that is critical to having a fully usable refrigerator but one that no one (even an authorized shop) has in stock. Just pop it back in, and you're done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Live Oak, FL
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rear mount tab broken on Center Crisper Rail
It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Los Angeles, CA
- Parts Used:
- WP67006877
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken glass shelf at bottom
Placed the new glass shelf in place on the crisper. Inserted the crisper into the slots where it slides in.
That was that.
That was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from COLORADO SPGS, CO
- Parts Used:
- W10121318
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
ICE BUILD UP AT BOTTOM OF FREEZER
DEFROSTED REFRIGERATOR COILS, BUT DIDN'T REPLACE THE GROMMET.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miguel from ESCONDIDO, CA
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Ladder hooks broke
Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Goldens Bridge, NY
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Refrig. was not holding proper temp in refrig compartment
Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherril from ROBBINSVILLE, NC
- Parts Used:
- WPW10503278
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
FREEZEING UP
in stalled new circuit board an thermostat an was fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from MT PLEASANT, SC
- Parts Used:
- WPW10503278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge running warm
The fridge would occasionally run warm, requiring me to turn it off and defrost the evap coils in the freezer. I found an online video that demonstrated the entire process of replacing the control board. The fridge model in the video was different than mine, so it took some time to figure out how to remove the panel. Once that was done, the rest was easy. The only tool required was a flat-head screwdriver that was used to push in the tabs holding the panel in place. The circuit board took more effort to split in two than I had realized, and I had to be careful not to bend any of the components on its surface. The whole process took less than 30 minutes, and the fridge is working properly now..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Oro Valley, AZ
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch on door broke
Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from Golden, CO
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke light switch while cleaning
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this instruction helpful to you?
Thank you for voting!