KTLA19EMSS01 KitchenAid Refrigerator - Instructions

Remove and clean out everything from the freezer and unplug the refrigerator. Take out the wire shelf in the freezer. (The fan motor is behind the back wall of the freezer, SO YOU CAN KEEP THE REFRIGERATOR CLOSED). Pop off the little cover on the center of the plastic shroud. Remove the little screw and carefully remove the plastic shroud. Remove the plastic cover for the optional ice maker on the upper left corner of the back wall. Take out the two screws in the upper corners on the back wall of the freezer and the last two screws holding the fan motor. The fan motor won't drop, remove the back wall and you will see two screws holding the motor mount. Remover those two screws, and pop the bracket out and separate.Take the two rubber motor mounts off the ends of the old motor and install them on the new motor. (Now you will have to cut the wires off the old motor), unplug the little wire harness, strip the ends and crimp on wire connectors to plug them onto your new motor. Its an AC motor so it shouldn't matter which hot goes on which of the two terminals. JUST MAKE SURE THE GROUND IS CORRECT! (After reinstalling the motor, plug in the refrigerator, turn it on before installing the shroud and make sure the fan is blowing outward. If all is correct, turn the refrigerator off, unplug and finish assembling the freezer. I found the new motor seems to run more efficiently than the old one.

After checking all connections I determined the ice maker which had been replaced on 01/2007 stopped making ice. I had serviceman from a local company return and check the ice maker. He rinsed the ice maker under warm water, melting the ice build-up and re-installed the ice maker. I watched him do the re-installation, then waited for two days to see if the ice maker was functioning. Since the ice maker wasn't working, I called the serviceman, who in turn informed me that the replacement ice maker had increased in price from $170.00 to $274.00. That is when I contacted your web site, ordered the replacement ice maker.
I was totally amazed and pleased by the fast,
easy, and efficient way my order was processed and the ice maker was delivered.
I followed the instructions included with the ice maker, and installed the replacement ice maker in about 20 minutes. I can't thank you enough for the great service. I only wish I had checked my computer after the first ice maker broke down and found your web site.

Unplug, then remove shelving and rear panel. Remove fan motor, swap wired and install new motor. Reinstall in reverse order. Plug back in and verify the fan is running. Easy and nothing special. Only thing I would caution is they use a foam runner to the refrigerator that may be iced up. Carefully clean the ice out before reinstalling everything. A follow up note. If the fan has not been running, Ice will build up in the drain tube. When you start up the refrigerator, you will see water dripping into the lower shelf. This is easy to fix. Unplug refrigerator and disassemble to where you can see the coils. There will be ice on the bottom covering the drain line hole. You will need to carefully chip away the ice, then use a hair dryer to melt the ice. Carefully use a pointed tool to push in the drain tube until the water drains. Go slow and be patient. Heat is your friend when doing this.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

We have a side-by-side and the tutorial was different than what we have. Had trouble getting cover off, but finally repaired and WE HAVE ICE! Also took longer than expected.
Saved a lot!

Removed the two screws that hold flaping door. Removed the single screw that covers the connecting wires. Disconnected the wiring plug. I wiggled out the ice maker. Took off the motor cover. Swapped out one motor for the other. Reinstalled the icemaker in the resverse order of removal. Note the wiring plug in the freeze is very from. It makine s the reconnection differcult.

Unplugged refrigerator, Removed lower back panel, Removed fan from fan bracket, Installed new fan to fan bracket, Installed new wire assembly to fan, Replaced back panel. Plugged refrigerator back in and it works great. Only tool needed was 1/4" socket.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

The repair didn't get done, because both times that I requested a 25-Watt Light Bulb, I received a 3.6 Watt bulb instead & neither one worked. So I tried testing the original bulb in a table lamp & it worked. So I sense that the problem may be in the switch that allows the light to turn on when the drawer is opened & shut off when the drawer is closed.

This site is so fantastic they even provided a video on how to install the cap. A job well done from a company who cares that you do it right. .

1.removed 3 nut screws-2 on top &1 on bottom.
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in about 2-3 hours

Easy removal. Easy Plug and play install. Didn't even have to use the other wires. After install, put 4 oz of water into ice maker and wait....it didn't start making ice right away, but a couple hours later I heard the wonderful "ice dropping into the bin" sound. Worked great ever since.

Remove the old part with pliers and pulled out used water filter Installed replacement water filter on cap and installed in grill area below door Hooray !

My brother came up and installed the part.

Removed the ice maker. Used a small mirror (wife's make up mirror) to find the screws. Inspected and found most teflon coating missing. Ordered new ice maker and installed. Works perfect.