KTRS25KGBL00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JONATHAN from ELKINS PARK, PA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old switch left freezer bulb always-on
Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Flagstaff, AZ
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light went out
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Vista, CA
- Parts Used:
- W10833899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water inlet valve
real easy to install and it works fine. However, the problem was more complicated. The circuitry on the ice maker on the back side of where the gear that rotates the harvesting fingers had places that were not making contact. I took a dart, yes, a dart from my dartboard and pressed the copper contacts down so they made contact and all appears to be well. Well at least until tomorrow. yikes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Shreveport, LA
- Parts Used:
- W10833899
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
ice maker quit
tested that water got to inlet valve, but not past it. the rod inside the pump was separated from the plunger. i ordered part. i was quite impressed that i got part within two days. replaced valve. ice maker works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Danbury, CT
- Parts Used:
- WP12550113Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Existing Door Gasket Was Leaking and Deformed
I followed instructions, both supplied with gasket, and some I found on-line. Pretty easy - loosen screws holding existing gasket, remove existing gasket, install new one, tighten screws. [TIP - I didn't soak new gasket in hot water before installing - definitely do this to get rid of the "wrinkles" caused by shipping. Throw it in a tub, and let it soak.] The problems I had to iron out were AFTER I installed new gasket. Door alignment shifted, so I loosened all gasket screws, realigned, and then tightened. Then door was not closing (it had dropped for some reason at the handle side), so I had to loosen hinge bolts, push up door, and re-tighten. I had to do this 3 times before door closed right. I also had to heat two sections of the new gasket with blow dryer to smooth gasket. After about two days, the gasket was sealing perfectly. No condensation in fridge, no leaking out bottom. I estimate by putting in a $100 gasket, I saved over $1,500 because my wife was ready to get brand new fridge. Good luck, and be patient if door needs to be realigned. Also - gasket may still have small gaps even after you install and heat it - give it a few days to conform to fridge before trying heat again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Millsboro, DE
- Parts Used:
- WPM0274057, 67007018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
We moved and the movers lost the bottom hinge assembly for the door
Went online and located the right part numbers. When delivery happened I put it together and all is fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cliff from Metairie, LA
- Parts Used:
- WP10097202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
compressor will not start - when you turn it on - it hums for a few seconds and them you hear a click sound (the overload opens) and the hum stops
be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Beauford, SC
- Parts Used:
- R9700006
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
refrigerator section was freezing food
replaced thermostat
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Woburn, MA
- Parts Used:
- W10833899
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
The ice making got slow.I replace the ice maker in December 2012 and it marginally until it stoped completely January 2014.
The Amana You Tube video explained and demonstrated how to isolate the problem. After finding the problem I ordered the Water Valve on a Sunday and I installed it Tuesday morning in about ten minutes.
Was this instruction helpful to you?
Thank you for voting!