KSSO36QTX03 KitchenAid Refrigerator - Instructions

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.

Very simple fix, remove 3 screws, two connectors to the old switch

I Removed 3 screws, pulled off the plate and put the new one on, screwed in 3 screws and away I went. I could not believe how easy it was to order the part and how quickly it arrived. I was very pleased. And I was literally screaming with excitement when I heard the first set of ice cubes drop!

I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Removed the Wiring & Troubleshooting instructions from behind the front Grill and used to troubleshoot the KSCS25IN side by side refrigerator. I then removed the three screws from the Emitter assembly on the left side of the freezer. Then disconnected the four pin connector. Removed screw holding emitter PCB to housing and replaced with the new PCB and then re-installed. Similar steps for the Receiver assembly and PCB on the right side of the freezer. Unit started making ice after making some water level adjustments on the Timer assembly.

I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.

Repair was real easy, I had to remove several screws in the bottom of the icemaker module housing. The unit slide out with no problem there was a wire assembly that hat to be disconnected but this did not present a problem. The old module came out real easy after removing 4 screws and the replacement was not a problem to but in.

I first had a technician come out to the house and he wanted to charge nearly $300 to replace the icemaker unit. I told him he was "high" and began doing my own research of the problem. That's when I found this website (thank God!) and read the notes from other customers. I figured out the secret location of the KitchenAid icemaker troubleshooting guide (why they hide this information I have no idea -- it's ridiculous), and performed the diagnostics to determine the exact problem. That is how I discovered that the emitter and receiver control boards were bad and not the icemaker motor module as the technician had tried to tell me. Good thing I didn't pay him, because my icemaker still wouldn't be working! The electronic control boards are a piece of cake to replace -- just 3 screws on each. Be careful with the electronical connectors since they snap in - don't pull on the wires, first unhook the snaps holding the wire connector to the board and then disconnet it. Once I replaced the boards I turned my refrigerator back on and immediately I heard the water running to fill up the icemaker and not much later I heard my first piece of ice hit the bucket. Woohooo!!!! It feels nice to fix a problem myself for a reasonable price. This site rules. I'll be coming here again in the future!!!

The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.

System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.

With the freezer door closed, remove 4 screws around the ice maker door assembly. Open the freezer door and remove about a dozen small flat-head screws around the sides of the door that hold the stainless steel cover to the freezer door. No need to remove the very bottom screws if you have something to support the cover with. Remover 4 hex-head screws that hold the ice/water dispenser control pad in place, use tape to secure this pad to the freezer door so you don't have to undue all the electrical connections. Remove two screws that hold the Ice Door Motor & Bracket Assembly in place - disconnect the electrical connection for the assembly. Replace the new assembly in the opposite order it was taken off. Presto - done.

Used u-tube video to review steps in making repair. Wires shorter than described but after looking at replacement sockets difference was clear.

i followed the online instructions on how to take the icemaker apart, which were very easy to follow. Once the new part arrived it plugged right in and a few steps later it was back together. within the hour we were hearing the sound of ice dropping into the tray. thanks for all the help this definitely saved us money and hopefully we get many more years out of this icemaker.