KSRS25MWMS03 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Adrian from REXBURG, ID
- Parts Used:
- 4389144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Evaporator Fan Motor quit working; top shelves of freezer got too warm
After viewing online videos of the repair process, it was very easy to replace the evaporator fan motor - just remove the back panel of the freezer compartment for EASY access to the evaporator motor. I received the new motor a day earlier than I thought I would. I took 15 to 20 minutes to replace the old motor. The only problem was the wiring on the new motor was on the opposite side of the motor as compared with the old motor. I was able to rotate the new motor enough for the new wiring to connect. VERY HAPPY with the results. A word of caution: the motor mounting brackets are plastic - go easy when trying to remove the brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Sugar Land, TX
- Parts Used:
- 4389144
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Catastrophic loss of cooling
It was straight forward enough--removed six screws from the metal cooling coil shield at the back of the freezer compartment and removed the shield. That left the motor and its mounting exposed atop the coil. Removed the electrical leads and popped out the motor and fan. Then I replaced the leads on the new motor, reset it in the mounting and pushed the fan propeller from the old motor on the spindle of the new. Twenty minutes tops.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Leonard, TX
- Parts Used:
- 4389144
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
fan was out of balance and rattleing-vibrating
I pulled the wiring harness off the bad motor, removed the fan blades (it was just a press fit and can be pulled off by hand), took out the three screws. The fan on the replacement motor had to be installed out of the fridge. I wiggled the new motor into place and installed the three screws. I cut the wiring harness off the fridge side and cut back the insulation. Using wire nuts I reconnected the wiring. I plugged the fridge back in and it worked like a champ.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from MORRO BAY, CA
- Parts Used:
- WP2182179
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
refrigerator door not working properly
Just as shown on your video.The refrigerator side was not sitting even, clunked and did not seal right. I decided to do.both sides, refrigerator and freezer while I was at it as our refrigerator is about 16 years old. Everything went in easily and saved us a lot of money. Very happy with the parts and repair video. Got the refrigerator nice and cleaned out while we were at it..Us and the refrigerator are breathing easier now..Yeepppeee....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Green Valley, AZ
- Parts Used:
- WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
old part cracked and broke
easy - remove the door, replace th part, put back the door
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from COLUMBIA, MD
- Parts Used:
- WPW10329686, WP2182179
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door no longer closing, washers worn down to nothing
Undo a few screws on top of door, replace closing washers at bottom part of door, put door back on, and done. Easy. Just make sure you have the top and bottom closer washers that go together...2 parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from N CHESTERFLD, VA
- Parts Used:
- WPW10321304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken door bin
simply set the new bin where the old one was.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from Afton, TN
- Parts Used:
- WP2223357
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rollers broken on meat pan tracks. Bin dropped to bottom of fridge.
Easily lifted existing frame out, inserted the new one and dropped glass tray in place. Could not have been any more simple in install. I am a 68 year old female. Two minutes tops!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stu from richmond, VA
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Phoenix, AZ
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
right side door not closing freely
Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Davis, IL
- Parts Used:
- WP2223357
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Meart pan cover roller on each side were broken which allowed the pan to sit on the bottom of the refrigerator
First I took the frame out of the box. Next I removed the drawer from the bottom of the refrigerator. Then I removed the old pan cover and glass from the refrigerator. I then placed the new pan frame into the slots of the refrigerator and then placed the old glass panel on to the top of the new panel. Next I slid in the drawer into the new frame. In 15 minutes I was all done. Thanks PartSelect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Roseville, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dorotea from staten island, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Sugar Land, TX
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigrator door made loud pop when opening and closing.
Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".
Was this instruction helpful to you?
Thank you for voting!