KSRS25MWMS02 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from STATEN ISLAND, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Freezer work perfectly, Refrigerator Stopped getting cold, water line froze, there was ice Forming around the condenser in the bottom of the refrigerator behind the drawers
Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from ENDWELL, NY
- Parts Used:
- WPW10225581
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Conyers, GA
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator door on a side by side unit would not stay closed.
First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from EASTON, PA
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem
just added new shelf - perfect fit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from ISLAMORADA, FL
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door bin broke
had my wife install them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from NORTH AURORA, IL
- Parts Used:
- WP2218119K
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Molded button on inside door panel broke off and compartment door fell and broke.
Used 2 Stainless bushings and a short screw to attach to side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from WILLARD, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elyse from Skokie, IL
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the light socket broke apart
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tammy from SHERMAN, TX
- Parts Used:
- WP2309941
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Shelf was broken on one side.
The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric S from Boca Raton, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench set
OLDER Ice Maker on the fritz
Grat help on the phone. We saw repair on YouTube. my wife and I worked it together. It was child's play!! It went beautifully. we were able to "chill out" with ice aplenty!!Thanks...eric
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adrian from REXBURG, ID
- Parts Used:
- 4389144
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Evaporator Fan Motor quit working; top shelves of freezer got too warm
After viewing online videos of the repair process, it was very easy to replace the evaporator fan motor - just remove the back panel of the freezer compartment for EASY access to the evaporator motor. I received the new motor a day earlier than I thought I would. I took 15 to 20 minutes to replace the old motor. The only problem was the wiring on the new motor was on the opposite side of the motor as compared with the old motor. I was able to rotate the new motor enough for the new wiring to connect. VERY HAPPY with the results. A word of caution: the motor mounting brackets are plastic - go easy when trying to remove the brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Leonard, TX
- Parts Used:
- 4389144
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Wrench set
fan was out of balance and rattleing-vibrating
I pulled the wiring harness off the bad motor, removed the fan blades (it was just a press fit and can be pulled off by hand), took out the three screws. The fan on the replacement motor had to be installed out of the fridge. I wiggled the new motor into place and installed the three screws. I cut the wiring harness off the fridge side and cut back the insulation. Using wire nuts I reconnected the wiring. I plugged the fridge back in and it worked like a champ.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.
Was this instruction helpful to you?
Thank you for voting!