KSCS25FVMS01 KitchenAid Refrigerator - Instructions

Actually, the part that was broken was a part that contained the slide that allowed the drawer to pull in and out which was connected to another part that held the drawer to the side of fridge.

I went on line to Kitchenaid.com, clicked on parts which brought me to a PartSelect website that made it really easy to find what I needed. There is an audio instruction guide to help you find what you need. I ordered it and it arrived in the next day or two. To install it I just had to snap it into place. Since I was already on the website I went ahead and order a new water filter.

Replacing this part was a breeze. But I could not believe how fast the part arrived at my doorstep - was expecting it to arrive in 3 days but it arrived in 2. And the part exactly the right one - the pictures on the sight helped a great deal in correctly identifying it.

I would absolutely order from here again and recommend it to friends.

Replacing my old ice maker with the new ice maker that I bought through PartsSelect was fairly easy. The part came without any directions - so I am glad that I did a little research on PartSelect prior to ordering. I am not the most mechanically coordinated person - but even with my large hands pulling the old ice maker out and putting the new one in was simple.
Only real problem was trying to snap the plug in and making sure that the connection was completely tight. With a side-by-side refrigerator - getting my hands and shoulders (I am a large man) far enough in to apply enough pressure to snap the connectors was a challenge.
Within 30 minutes, my wife heard the ice maker making ice - I was a hero and I had saved about $150 in the labor I was quoted.

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

On this model, access is very easy. The tray slides forward, and then lifting up with a little force at the back of it clears a stop, allowing it to slide out. This exposes two Philips/sq2 screws that hold the faceplate in place. The faceplate swings out and is lifted off the top edge. Disconnect the wire harness and set aside. Trace the cable from the door motor to the control board. Disconnect the cable and fish up behind the facing material. Remove screws holding the dispenser door mechanism. On that assembly, remove the screws holding the motor to the mechanism. Replace the motor. Put the mechanism back in place engaging the metal actuator arm in the door. Fish the cable down to the control board and plug in. Plug the faceplate wiring harness back in, and reinstall the faceplate. Secure with two screws and replace the tray. Done.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Simply cut the water tube on both sides of connector and push in the new one.

I replaced this same ice maker a month before, if that long, using a part I found $40 cheaper from another site. Needless to say you get what you pay for, the existing part was not exactly the same as the original and leaked water all over the place. I removed the not so old icemaker by removing the flapper door and removing the harness cover then pulling out the existing icemaker followed by disconnecting the wiring harness. Now with the old icemaker removed I removed the bottom tray/shield from the existing ice maker by removing the three screws from it then attached the tray to the bottom of the new ice maker from PartSelect which did not come with the bottom tray/shield. Finally, I executed the removal process in reverse order to install the new ice maker.

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

I removed two small bolts that secure the flapper that keeps ice from falling out when you open the door, one bolt that holds a cosmetic cover for the wires and slid the icemanker forward. The only difficult part was removing the plug since it was high up, the wires were stiff and there's a release to push that locks the two plugs together. Once it was removed all was installed in the opposire order.
The part I ordered had a slightly taller channel where the water refills so I had to trim it to allow the new icemaker to slide in without bending the fill nozzle. Other than that it was pretty easy.

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

The cap will only fit on one way. Align with tabs on filter, twist on. Press the filter into place and press to seat. Locks into place.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.