KSRS22MWMS02 KitchenAid Refrigerator - Instructions

easy - remove the door, replace th part, put back the door

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Followed easy installation instructions which were helpful

Just as shown on your video.The refrigerator side was not sitting even, clunked and did not seal right. I decided to do.both sides, refrigerator and freezer while I was at it as our refrigerator is about 16 years old. Everything went in easily and saved us a lot of money. Very happy with the parts and repair video. Got the refrigerator nice and cleaned out while we were at it..Us and the refrigerator are breathing easier now..Yeepppeee....

Parts ordered and received within 2days
Opened box, removed old bins and just replaced with new ones,
I am happy when ever I open my refrigerator
Nice product whirlpool!!

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

Because the bins fell to a ceremic floor they broke and as no longer useful.

Removed right hand door of side by side. Replaced both cams and put door back. All is well.

i didn't repair replace capacitor, bi metal defrost thermostat and still not freeze also replace light door switch any suggestion thanks

Removed old thermostat and installed new one.

Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now

DISCLAIMER: Technically, you should start by unplugging the frig and turning off the water supply. Though there is nothing on the my frig door that is either electrical or water related, the frig does keep trying to cooling an open area. For the short while I was doing the work, I just didn't want to bother with those precautions. Had I expected the work to take longer or been working on the FREEZER door I would have most certainly have done it "correctly." But I didn't do the freezer door so, first, remove everything from the refrigerator door storage shelves and the shelves themselves. Then lift off the cap that covers the hinge mounting plate on top of the frig. Remove the screws that holds the mounting plate in place. I used a cordless drill/driver with a 1/4" socket on the end but this could be done with a nut driver or socket wrench as well. Of course, take care not to let the door fall when removing the last screw. Then, lift the door off the bottom post that his holding it in place. The door is not too heavy and one person should not have a problem doing this but if you think it might be too heavy get someone to help with this. On the frig door there are no other connectors to be concerned with. NOTE: This procedure is similar for the freezer door but there are electrical and water line connections that need to be addressed before removing the door. Once the door is off the post, lay it down on a flat work service (I used the kitchen table with some towels spread underneath to prevent scratching either the table or the frig door.) There are two pieces that ought to be replaced. One cam on the door and one at the bottom post. Both are attached with a small screw that is removed easily with your nut driver/socket/drill driver. The bottom cam came offer fairly simply but sliding a thin, flat blade screw driver under it and prying it up and off. Replace this bottom cam with a new one and screw it back down. The door cam was, for me, the more difficult item. Removing the screw was easy enough but years of wear and brittleness led it to break off as I was trying to pry it out. I was able to use a small flat blade screwdriver to cave the old plastic post in all around the insert hole until I could get a good hold and pull it out with needle nose pliers. I was tempted to try to drill the old post out but there is a hex shape to the insert hole I was afraid of ruining. Once I got the old cam out, it was a simple matter to re-insert the new cam. Since both the door and lower cams are held on by screws there is only one way they can go back on. Once the cams are back in place, lift the door back onto the post and reattach the mounting plate to the top of the frig. Take some care that the door is level and parallel to the freezer door before completely tightening the mounting screws and replacing the cap that covers the plate. If you did shut off water and unplug the frig you should turn it back on and plug it back in. And do I really need to tell you to put the shelves and stuff back? :) The door should close on its own when close enough to the frig frame that the cam notches slide into place. If it hadn't been for the door cam being so brittle, this repair would have quite simple. Even at that, digging the old post out really wasn't hard but it did take some unexpected effort. If your refrigerator door is not closing properly, this is something anyone with basic skills can do.

First I removed the three screws on the top hing of the refrigerator door so that we could lift it off the bottom hing. Socket wrench bits for my drill made that fast and simple. I lifted the door off the bottom hing to find the door closing plastic cam to be broken in several pieces. The hardest part was getting the cylinder shape piece that had broken off the cam out from inside the door. This way we would be able to insert the new piece. Needle nose pliers are the right tool for that job since the hole is small and the plastic just frays under force from regular pliers. It took some force and patience to get that out, but once all the broken pieces were removed, reassembly was quick and easy

I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks

It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigerator is still too wide but it's colder.