KFIS27CXBL0 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Empty box sent with no part!!!! No customer service help because of covid
No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THOMAS from Titusville, FL
- Parts Used:
- WP12956105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water inlet valve stopped working.
Turn off the water to the unit. Disconnect the plug on wiring from the old valve.
They always recommend you disconnect the electric (unplug) the unit while doing this work.
Disconnect the water lines from the old valve by pushing the water line slightly into the flange on the valve, it releases the line from the flange.
Hold the flange rim against the valve seat and pull, you may have to jiggle the water line a little while pulling to remove it.
Push the water lines into the ports on the new valve, turn on the water and check for leaks.
If no leaks, plug the wire connections onto the new valve, reconnect it to the unit and turn the power back on.
They always recommend you disconnect the electric (unplug) the unit while doing this work.
Disconnect the water lines from the old valve by pushing the water line slightly into the flange on the valve, it releases the line from the flange.
Hold the flange rim against the valve seat and pull, you may have to jiggle the water line a little while pulling to remove it.
Push the water lines into the ports on the new valve, turn on the water and check for leaks.
If no leaks, plug the wire connections onto the new valve, reconnect it to the unit and turn the power back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from EASTON, PA
- Parts Used:
- W11396037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
gasket had ripped over the years where they flexed when dooors were opened and closed.
last time i tried it right away after removing from shipping box.. relaxing with with hot air gun... was not to easy... this time i allowed gaskets to relax for a week on a flat surface. in a warm room.... took less than 5 minutes per door.... no hot air needed.... VERY easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerome from Goldsboro, NC
- Parts Used:
- WPW10714545
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer door leaking on floor.
Open and remove door by loosening two screws on both sides of the door. Lift up and away the door.place the door on flat surface, grab and lift up on seal pulling out of reach. Clean track, alone seal on food before pressing in place. Check to make sure seal is set in place. Install door job done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from N LITTLE ROCK, AR
- Parts Used:
- W10830055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Existing Door gasket was cracked allowing the magnetic strips to fall out
Very easy. Just get hold of the gasket with your strong fingers and pull it out of the groove it is in. Clean the groove, I used Windex and paper towels. On the new gasket there are 2 wide areas on the vertical part. these must be facing toward you and on the handle side of the door. start at the tor center of the door and work the gasket in with your fingers outward to the corners then work on the bottom of the gasket in the same manner, then start on the vertical gaskets. when you think every thing is aligned take your thumbs and press very hard all around. You may have to repeat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from HOUSTON, TX
- Parts Used:
- W10830055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Gasket just wore out was leaking
Once I took new gaskets out of carton
and put out on patio to warm up I removed old gaskets pressed in new gaskets which made a great seal
Job was easy and took no skill
and put out on patio to warm up I removed old gaskets pressed in new gaskets which made a great seal
Job was easy and took no skill
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from LELAND, NC
- Parts Used:
- WPW10212139
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door shelf cracked
Removed old shelf and installed new shelf. No tools required
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from WINSTED, CT
- Parts Used:
- W10619951
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Water not draining to pan. It caused an ice build up under the freezer draw
Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from THE VILLAGES, FL
- Parts Used:
- W10830055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Gasket Torn
Removed old gasket and installed the new one. Used a hairdryer to smooth out the edges.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MABLETON, GA
- Parts Used:
- W10619951
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Easy fix for Whirlpool refrigerator
I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HARRY from FSTRVL TRVOSE, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer drawer light switch failure.
Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from SMITHFIELD, RI
- Parts Used:
- WP12825803
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
I had a loose fitting old condensor fan blade on my new motor.
I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from BROOMALL, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The door switch was broken so the interior light would not come on.
The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from ST CLR SHORES, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Austin, TX
- Parts Used:
- WP2220457
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Frost build-up in freezer at ice door opening
The only real difficultly I had replacing the ice door was getting the exterior trim off the freezer door. You have to push down on the bottom of the trim to release the tabs that hold it in place. After removal of the trim, the rest of the repair is pretty straight forward.
The ice door kit solved the problem!
The ice door kit solved the problem!
Was this instruction helpful to you?
Thank you for voting!