KSRJ25FXMS02 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gregory from NORTH AURORA, IL
- Parts Used:
- WP2218119K
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Molded button on inside door panel broke off and compartment door fell and broke.
Used 2 Stainless bushings and a short screw to attach to side of door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from Lawrenceville, GA
- Parts Used:
- W11629974
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator would not stop making ice
Easy repair, unplug the fridge and then remove the 3 screws on each side of the freezer holding the emitter and receiver. Swap the boards and re-install. Takes less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steven from long grove, IL
- Parts Used:
- W11629974
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker stopped making ice
Unpluged fridge, removed 3 screws from each control board (1 on left side and 1 on right side in freezer below ice maker compartment, unplugged and swopped out with new ones. Did one side then the other. Learned about the issue from other people on PartsSelect. Coulden't have been easier. Got parts in 2 days. Works like a charm now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TAK from NEW ROCHELLE, NY
- Parts Used:
- W11629974
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker not making any ice.
I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James P from Mansfield, TX
- Parts Used:
- WP2255720
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice Maker door broke off
Snap the new one into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from EL PASO, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No Problem
Just needed to replace the water filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from MEDWAY, MA
- Parts Used:
- W11629974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker continued to make ice - would not turn itself off
followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from ST PETERSBURG, FL
- Parts Used:
- W11629974
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No ice
Removed the cover plates and unplugged bad boards. Hard to plug in boards after attached to cover plates. Plug in boards first then attach to mounts. Ice in 4 hours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TAMMY from SAN ANTONIO, TX
- Parts Used:
- WP2260518MG
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cap clasp broke
trashed old one, slipped new one on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyner S. from MIDLOTHIAN, VA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Time to replace filter.
I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Victor from CEDAR CREEK, TX
- Parts Used:
- WPW10191429
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Both Upper Lights Burned Out Same Time
The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.
Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.
Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George S from LEWES, DE
- Parts Used:
- WP2218119K
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cracked cover to the dairy shelf.
Squeezed the sides of the cracked cover.
Slid the cover out of the shelf.
Reversed the process with the new part.
Slid the cover out of the shelf.
Reversed the process with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alexander from ANDERSON, SC
- Parts Used:
- WPW10121138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Filter housing was leaking under the refrigerator
I looked up the video on part select for how to replace the filter housing. Seeing it was fairly easy, I order the parts, which arrived promptly. Then, once I had some free time, I uninstalled the old housing and installed the new one. Following the video made it easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from HOUSTON, TX
- Parts Used:
- 4387478
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Faulty light socket
Followed the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from El Sobrante, CA
- Parts Used:
- W11629974
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker stopped
Called a repairman out. For $125 he told me what I already knew! The ice maker wasn't working. Said I needed new emitter boards and ice maker. Would go back to the shop and call me with an estimate. Estimated parts were $330 plus another service call to put them in.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.
Went on line and found PartSelect. Emitter boards were $87+shipping. Ordered. Arrived in 3 days. 3 screws on each side. Unplugged old boards. Plugged in new. 15 minutes. Still did not work. Took out ice maker and examined. Gear that drives ice ejector fell off. End of shaft broken. Ordered new motor unit from PartSelect. $61+shipping. Arrived in 2 days. Loosened 1 nut screw. Slid ice maker out. Unplugged. Removed motor cover. 3 screws removed motor. Replaced with new motor and reassembled. 15-20 minutes max.
3 hours later had ice coming out for under $160. Wish I had known sooner. Thanks PartSelect.
Was this instruction helpful to you?
Thank you for voting!