KSRJ25FXMS00 KitchenAid Refrigerator - Instructions

pull the fridge out away from the wall and hope you have a long flex water supply hose.remove cardboard cover,oh yea unplug fridge first.unplug wire from the relay.flip the wire retainer off the relay and pry it away from the compressor.pull the 2 prong capacitor off and then reverse the steps to reasemble. skip the middle man at the local appliance shop.i waited 2 weeks for him to get the part and gave up.your reg shipping got it here in 2 days.

Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

watched video. Very easy

Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

First off you need to shut off the water supply valve that goes to the icemaker. Next pull the refrigerator from the wall , thats the fun part. I did not unplug my refrigerator when I did this . You can to be extra safe. At the bottom on the back side remove the cardboard cover on the bottom like four or five screws and set this aside. The water valve is on the bottom on the right side. There are 3 water lines attached to it. Having a towel handy might be helpfull. 1 line supplys the water, 1 is for the water dispenser and 1 is for the ice maker. These are push in connections no wrench needed. Remove the 2 screws that attach water valve to frame. Arrange it to make removing the 2 wire connections and water lines easier to remove. Wire connections just pull off. Mark them as to what valve they go to. Next remove the water lines. you need to remove a plastic lock that insures that the water lines do not pop off, very simple. Next push down on the nylon connector push down on the top of connector and pull on the plastic water line at the same time and it will come out. Do this to all 3 water lines. Remove old water valve and install new one in the reverse order. The water lines just push in no need to mess with connector when line is in reinsert the plastic lock. Reconnect the power connections. Align the water valve bracket with screw holes in frame and reattach the 2 screws holding it in place. Now would be a good time to turn on the water and check for leaks. You can check water dipenser but ice maker has a mind of its own. If all is good reinstall the cardboard cover on the back bottom and push refrigerator back where it was. Make sure the water line is not kinked. Aftre a couple of hours the ice maker should start making ice.

took cover off, installed bulb.
lost the owners manual,
part select's schematics were very helpful
thanks

First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.

Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.