Models > KFIS27CXMS3 > Instructions

KFIS27CXMS3 KitchenAid Refrigerator - Instructions

Jump to:

All Instructions for the KFIS27CXMS3
106 - 120 of 253
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Daniel F from CALEDONIA, MN
Parts Used:
W11613295
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Freezer and refridgerator just stopped working.
The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christine from SAN DIMAS, CA
Parts Used:
WPW10714545
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
The freezer door was not staying fully closed.
I watched a YouTube video real quick to see what I had to do and got to the job at hand. I removed the old gasket by pulling it out of the track and bring it around the front of the drawer. I wiped down the entire area where the new one would go and started inserting it into the groove, making sure it went in completely in on the bottom. I was done in less than 15 minutes. Super easy! This fixed the issue and the freezer door closes fully.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from AUBURN, CA
Parts Used:
W11396033
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from PHOENIX, AZ
Parts Used:
W11613295
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
CHRISTINE from MARBLEHEAD, OH
Parts Used:
WPW10534153
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Needed to replace old kickplate as it no longer was attached
Put new one on matching the sctew feet and design of the grill
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from McKinney, TX
Parts Used:
W10619951
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Water pooling on the floor.
This problem is caused by a "Duckbill" rubber grommet attached to the bottom drain tube of the freezer. This duckbill opens up during the defrost cycle and allows water to drain down the "water slide" to the evaporator pan. It doesn't take much to gum the Duckbill. Once gummed up the defrost water is trapped. The Defrost Cycle eventually makes the water flow out of the coil area to the bottom of the freezer then eventually to the floor. The repair involves unplugging the unit, removing the bottom back cover with a 1/4 nut driver, pop the power clip out to give you room, reach in and pull the duckbill grommet and the water slide, then installing this replacement drain kit. This is a p trap replacement that actually fixes the root cause of this problem. A tricky part is removing the water slide, you can see the white snap that holds the slide in place. Using a small flat blade from the top releases the snap and the unit is pulled upward rather easily. This replacement drain clip snaps in the same place. If I had to do this again it wouldn't take more than two minutes to replace. Oh, one major thing, you need to manually defrost the unit. I pulled the front door off, it is held with 4 screws ... don't remove them just loosen them and it pops off easily. I pulled the bottom tray out an it gave me room to squirt hot water with a baster into the back freezer area. Eventually everything thawed out. If I had it to do over I would have waited on connecting the tube to the evaporator pan and placed the bottom of the tube into a small sauce pan or something to collect the drain water and easily dump it into the sink. I used a sponge and that took forever. BTW, just to reiterate, use this item and not that Duck Bill for replacement, this actually fixes the root cause of this problem!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOE from BATON ROUGE, LA
Parts Used:
W10679370
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Wrong Part Sent (interior light)
I received the wrong part - had to pay returnin shipped and restock fee. Lost out on dealing with this company. Went to Whirlpool site and got correct light for my refrigerator
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ronald from HUNTINGTN BCH, CA
Parts Used:
W11396033
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Wayne from Red Banks, MS
Parts Used:
12002497
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Broken Freezer Drawer Gear
Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from DUNNELLON, FL
Parts Used:
WP2198628
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Socket set
Ice maker grinder motor was not running.
Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Roger from SMITHFIELD, RI
Parts Used:
W11613295
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
The referigerator is warm, but the freezer is cold.
I noticed the coils very dusty dirty, tried brushing it clean, ended up blowing it clean. I noticed the condenser fan motor was never turning, I had power, so I ordered a new one. I actual received the evaporator motor, so I had to order the correct one. After changing it, and it started blowing right away. But my refrigerator is still warm. I do not know where the evaporator blower motor is located. I cannot make out from the diagram breakdown. HELP
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Daniel from CENTREVILLE, MD
Parts Used:
WP67003405
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Needed to replace pivot block (broke) so frig door extension could close
Can not do repair. Ordered part 3/30 due to me on 4/1. Today is 4/15 and still no part. I even paid for quicker delivery. Thanks FedEx!!
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from Shrewsbury, MA
Parts Used:
W11396033
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Broken light switch
Pried out the old switch and installed the new switch.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Rod from Jacksonville, TX
Parts Used:
8201515
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Ice maker on fridge would not make ice.
Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Austin, TX
Parts Used:
8201515
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Ice Maker Motor Broke (Plastic Cogs)
1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KFIS27CXMS3
106 - 120 of 253