KFIS20XVBL5 KitchenAid Refrigerator - Instructions

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

Removed old ice maker by removing 3 screws, unplugged wiring harness. Replaced with new ice maker, placed three screws back to secure the ice maker, plugged wire harness back, and product is working well at this time.

one screw and electric plug and the unit slide out. Slide the new one in and your ready to go.

we removed all the lower stuff,so we could get to the part.
unscrewed all pieces 3 screws
than removed it all in order..
than the hard part came ,when we had to figure out how to remove all the moving parts.from the back ..after a little wiggling we figured it all out and got a part...the new piece in and all back together...my husband and i did it in about 45 minutes,,,also gave us a chance to get those really hard places in the back to clean...thanks for all your help in helping me id the part..
thanks
linda landsdowne

Remove crispers & bottom drawer. Removed glass piece. Unscrewed piece( small nuts not screw heads) There is also a nubbie at front. You must remove by sliding out & lifting back of part. Reuse screws to replace piece & drawer runner. It took 15 to 20 minutes. I am all thumbs. If I can do anyone can do!

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

Unscrewed all related parts and also took out drawers and glass shelf. Reused plastic slider which raps around right corner to the back wall of the unit. Make sure to remember how this plastic slider fits into the new end cap, it is a little tricky putting it back without cracking it. Suggest take a digital picture as to how it fits together before taking the slider out of the old end cap. Reinstall same way as you took it out. Good time to clean while everything is out of the bottom of the refrigerator.

Remove back cover
Remove drip thing from top to tray in the back
Remove fan motor assembly. This is squirrely. Top bends towards you, bottom pushes in to the unit. Not fun.
CAREFULLY remove copper tube that rests on drip tray
Remove tray - there are clips in the front that get released by screwdriver
Clean up
Replace new tray
Replace copper tube
Play with fan motor assembly till it fits. It doesn't look like it's gonna work until it does. See youtube videos on this.
Replace drip thing from top to tray - I forgot this one the first time.
Replace cover.

This is a simple, but squirrely, repair. Right on the border of easy (because so few tools and steps) and A Bit Difficult because of the patience required.

Saw U tube instrctions how to install and it was easy

Let the ice in the freezer melt while installing P trap drain tube

Replaced water/ice maker inlet valve from video instructions from Just Answer. The inlet tube for the water dispenser would not cede in the valve and this created a leak problem from the water dispenser connection. Called repair tech and he could not get the line to cede correctly in the inlet valve. Am going to request a replacement part. This has been very frustrating!

I removed the right side endcap and rear thermostat piece behind the pull out drawer. It was fairly quick, 3 screws on the exterior of the end cap and one screw holding in the drawer thermostat. The worst part was getting the thermostat control that connects the drawer thermostat control to the rear thermostat. After playing with the control rod I was able to to snap it in successfully to the endcap with the proper rod connection. The rear thermostat goes in first, then the endcap. Quick and easy. For $23 it would have cost over $150 to call a repair guy ($120 call charge plus parts). Thanks.

Looked at the new part to determine what I would need to remove the old part. It was very easy to figure out. I removed the old end cap by taking out the screws. Once the screws were out I popped the side of the end cap off. There is a horizontal piece along the back wall that is connected to the end cap. On the left side of this piece of plastic there is a small tab that clicks into the back wall. On the right hand end cap there is a sliding lever which controls the air in the deli tray. This control is made of plastic and appears to be pretty fragile> By gently bending this lever I was able to remove the control lever and install it on the new end cap. In all it took me about 15 minutes to complete the entire job. Very easy.