KFFS20EYMS00 KitchenAid Refrigerator - Instructions

Removed all food! I used storage boxes insulates with blankets and a bit of dry ice in the boxes to keep the food cold.

Removed bottom bin and shelf

Removed bottom cover and fan shroud, this exposes evaporator coil and the thermostat. I had to defrost the evaporator and thermostat, they were completely encased in ice.

Thermostat is clipped to the evaporator coil, simply pry it off and removed it from the wire harness. Easy! Thermostat has a connector!
Installed new thermostat in the same location as the old one. Connected it to the wire harness and replace the bottom cover.
Turned it on and it seems to be working fine, now three weeks after repair.

took back off refrigerator read directions that was sent with parts and replaced the wore out drain nozzle . Even this 70 year old woman could do this her self and changed air filter in refrigerator also

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

pulled the top shelf and poped open the door and replaced the filter

Took the old one out & replaced it with the new one

I failed to repair the problem and sent the parts back. The hinge bracket that I needed was WPW10524049. The hinge that I purchased was WP2183805. I gave up on trying to repair the door because it was not clear to me how to assemble the cam and hinge. There doesn't seem to be any obvious way to disassemble the hinge and cam that I have - which would allow me to replace the cam in the existing hinge.

This one is not as simple as popping it into channels or screwing it in.

I opened the freezer and removed the door from the drawers. To install it you need to hook the back of the gasket behind the white freezer liner. Mine was difficult because it seemed too small. I had to clip it behind the liner inch by inch. If you are not careful the gasket will pop out and you’ll need to start over. Definitely recommend you try with another person. If instructions were supposed to come with the gasket, they did not.

Super simple job. Unplug freezer. Have a hair dryer handy to defrost while you have unit open. Remove food from the bottom two shelves and floor of freezer. Remove mid plastic cover removing three screws. (All screws are same so mixing them is no big deal.) Use drill-driver or screw driver to spin out six screws on lower back plate. Remove plate. Thermistor is on left side of the cooling tubing. Use hair dryer to melt ice if necessary. Un-clip thermistor power connection, and unsnap it from tubing. snap new thermistor on cooling tube and hook up wiring. Ensure plug fits together correctly and snugly. If heavy icing exists, use hair dryer to melt ice on coils and through fan. Ensure water drains out of drain pan under coils. Wipe up as much ice melt as possible to prvent re-frosting upon start-up. Replace lower panel and six screws. Replace mid-panel cover and three screws and replace shelves. Done! Plug freezer back in and expect 30 second delay before unit will start up.

Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.

But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.

Maytag should recall that Rocker Switch and build with better materials.

The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Followed online instructions. UnPlug and Plug in new part

this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?

After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!