K9TREFFWMS00 KitchenAid Refrigerator - Instructions

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

shook bottle and painted waited a day and repeated

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I followed the instructions in the video on the PartSelect website. The only problem I ran into was that I couldn't switch the grounding tab connector from the original side of the motor to the other. I had to add more wire so that I could reach it in its new location.

I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.

1. I removed the plastic back cover panel in the freezer. 2. Took flash photos with my phone of the motor and wire configuration. 3. Removed noisy Evaporator fan bracket from freezer. 4. Removed Fan Blade from old Motor. 5. Removed old Motor from Bracket. 6. Installed New Motor into the bracket. 7. Installed the fan blade onto motor spindle. 8. Installed the bracket onto the back wall of freezer. 9. Noticed that the tab for the ground wire was inaccessible. 10. Cursed like Linda Blair in the Exorcist for about 5 minutes. 11. Repeated steps 3 - 5... 12. Unscrewed the ground tab and placed it on the opposite side and screwed it back in. 13. Repeated steps 6 & 7.... 14. Tried to install the bracket and motor back onto the freezer but the bracket screw holes weren't lining up. When I removed the motor to flip the ground tab over, I reinstalled the motor onto the bracket upside down. 15. Tear some hair out of my head. 16. Repeated steps 4 & 5 and flipped bracket over. 17. Repeated steps 6 - 8... 18. Placed wires onto tabs. 19. Ground wire would not stay securely onto the tab. 20. Slightly opened up metal fastener of ground wire with needle nose pliers and stuck it onto the tab. 21. Still not on there super tight. I gave up wrestling with it and just prayed it will stay on there anyway. 23. Turned on freezer to check if it works. 24. Reinstalled plastic back plate. 25. Put melted food back into freezer.

Ordered new set and installed

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

Looked at your You Tube video and followed the instruction

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

poured boiling hot water into drain; removed most ice with hair dryer. Clips(2) positions the defrost tray & drain under the freezer condenser. A "home-made" coil of 18g copper wire inserted into the drain hole, & secured to the defrost heater further prevents the drain from iceing shut!

much like yout video. However I got the mounting bracket upside down and had to do the job twice. When finished it worked perfectly. Great! However in Missouri outside temperature was over 100 and refrig was in shed. My beer got warm. Thank you.