KSRA25KNSS01 KitchenAid Refrigerator - Instructions

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.

The repair was incredibly easy. The only reason it took me so long to do it was that the instruction sheet did not make it clear that the parts supplied covered 4 possibilities. It took me a long time to realize that in my case (the discrete) I only needed to use the separate relay, one of the funny shaped parts, the jumper wire, and the cover, but not either of the combo versions. Maybe I'm dense or just too cautious. However, once installed, the fridge started up and is working fine.

First, let me say that PS was unbelievably fast in getting the part to me ... Extraordinary, in fact. Unfortunately the new part was not the same dimension as the old one ... the four plastic arms that extend through the wall from the refrigerator side to the freezer side and secure the part in place measured a full 1/4 inch shorter than those on the original part ... Even with much effort and a few choice words, it was impossible to get the arms to clip into place ... It wasn't,t even close. So, we used our fine-toothed Swedish saw to take off 1/4 inch of the large part of the styrofoam "housing" so that the arms would extend farther into the freezer side ... Even then, it was difficult to get the arms clipped into place. If the part had been the proper dimension, it would have been a 15 minute job - just remove top two shelves from both sides and move ice maker out of the way ... Just need a nut driver to remove two screws from fridge side to get the two cover plates off and one screw from ice maker ... Push part from freezer side to fridge side, pull wire plug off old unit, plug into new unit, push unit in place on fridge side until arms click in place, replace ice maker, cover pieces in fridge, and shelves. Unfortunately, we didn't get a part that fit. Unfortunately, after all of that agony, our problem remains. We had replaced the bimetal defroster first, which also was delivered quickly. It was different from the original, but it fit and was easy to replace. Next we'll try the thermistor! Incidentally, I agree with an earlier reviewer ... Kitchenaid is junk - not the same since Whirlpool acquired it ... Same with Maytag, in my opinion. Thank goodness for Partselect.com!

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

Used 2 Stainless bushings and a short screw to attach to side of door.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Well - I simply snapped the new shelf into place and vwah la - I have an extra shelf now in our very crowded freezer! Hurray!!!! Super easy.

Very simple fix, remove 3 screws, two connectors to the old switch

Slapped it on with the Palm of my hand and slid it back until it reached the end of the slot. Replaced deli drawer. Took all of 30 seconds.

Undo a few screws on top of door, replace closing washers at bottom part of door, put door back on, and done. Easy. Just make sure you have the top and bottom closer washers that go together...2 parts.