KSRP22KDWH01 KitchenAid Refrigerator - Instructions

Used 2 Stainless bushings and a short screw to attach to side of door.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line which we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.

Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam aligned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.

It was straight forward enough--removed six screws from the metal cooling coil shield at the back of the freezer compartment and removed the shield. That left the motor and its mounting exposed atop the coil. Removed the electrical leads and popped out the motor and fan. Then I replaced the leads on the new motor, reset it in the mounting and pushed the fan propeller from the old motor on the spindle of the new. Twenty minutes tops.

Followed easy installation instructions which were helpful

We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel was easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.

My husband is an appliance man and he did the work.