KSRA22ILSS02 KitchenAid Refrigerator - Instructions

ridiculous how a tiny plastic broken part required a full motor assembly replacement. that being said, i went online, found this website and easily identified the part i needed to order. i was impressed when it arrived within a couple of days. removing the old motor and replacing the new was a piece of cake...and i am NOT mechanically inclined,

I watched several video's on youtube that showed me how to replace the parts. Just Google "how to fix my freezer". I figured the only problem was the freezer Thermistor so I only replaced it. The refrigerator has one to. Instantly the freezer went back to Zero degrees and the defroster works fine after melting all the ice in the bottom. Make sure the drain hole is cleared. I ordered the bi-metal thermostat just in case but I don't need it. Be sure and position the thermistor down in the freezer rail on the right side just to where you can see it in the first opening and pull it back up out of sight and tape it to the wall where it comes through from the air baffle. It's important that it's 7.8 " down from the top of the freezer. Happy now, Freezer 0, refrigerator 37. This thing use to run all the time, I'm saying electricity now.

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

I removed the cover for the lower part of the refrigerator to inspect the wiring and motor. I removed the switch and removed the wiring from it. The wiring just plugs in. When the new switch arrived, I just reinstalled it to the side of the motor and the refrigerator has been working fine ever since.

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

found power up to current relay but not to compressor. removed the old current relay and installed the new relay and the compressor started running and the refrigerator works fine now.

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.

Read the instructions that came with the relay/overload.

Determined wich of the relays and overloads in the kit supplied was needed on the refrigerator.

removed the old relay and capacitor.

Simply installed the new parts .

Back in business.

Thanks for the quick delivery.

Replaced the entire unit (fan and motor). Would have rated this repair as "Really Easy", but found it a little difficult because of large hands.

Ordered Part Number and overnighted shipping. Took less than 5 minutes to install the kit. Refrigerator Works GREAT!!! FYI, I called a repair service and they wanted $300.00 to come out and repair. The part and shipping were $76.00. I saved a ton and did it myself!!!

With the exploded (Printable) view of the assembly for my fridge available on this site, it was a breeze removing the existing ice dispenser motor and replacing with the new one. Ice dispenser work like new, now. I have never had a bad experience from Parts Select.

remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ran around 30 with shipping.

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..