KBRS22KGBL13 KitchenAid Refrigerator - Instructions

First we read all the comments by other handymen. This was really helpful. Then we took the door off and removed the old gasket with a nut driver. We tried to slip the new gasket under the edge with a thin spatula and didn't have much luck. Then we remembered someone saying that is was a good time to take the door apart and check to see if there was ice build up in the door. It was so bad we took out the frozen insulation and replaced it with new....$4.00 at the hardware store. While the door was apart we put the gasket on and put it in place and tightened it to the door. This worked very well for us. This saved us from having to buy a new refrigerator/ freezer. Thanks.

1- Remove food from freezer and store in ice chest
2- Turn off refrigerator
3- Remove freezer drawers, 2 drawers, no fastener
4- Remove freezer slide out drawer front , 2 screws
5- Remove ice cube tray holder, 2 screws
6- De-ice back panel with hair dryer / blower
7- Remove back panel in freezer, 8 screws
8- Defrost refrig coil with hair dryer / blower
9- Unplug Bimetal Thermostat, 2 wires, orang / brn
10- Remove Bimetal Thermostat from coil, 1 clip
11- Install new Bimetal Thermostat
12- Re-assemble, reverse order

carefully

First of all let me say I can't believe I fixed it! And I can thank this website for it, they also had my part at my front door in less than 24 hours. I am so amazed! I am a stay at home Mom, and because my husband is always off with the military I knew the job was up to me to fix. And because times are tough we certainly couldn't afford a repairman. After reading many stories here about the same problem I had, I diagnosed what was wrong with my refrigerator. The defrost thermostat was faulty. First thing to do was turn off the refrig and then unplug it. I then emptied the bottom freezer, used a screwdriver to remove back panel wall. Lo and behold the coils were covered with ice. I defrosted the freezer using a blow dryer, also had to empty the drip pan in the back. when it got full of water. ANd because there is no way to remove the drip pan, I actually got a small air hose from my son's old fish tank(clean one) and then siphoned the water into a pot, took all of 10 minutes! I then used needle nose pliers to remove the bad defrost thermostat from the refrig's wiring.The defrost thermostat which had a bulge in it so knew I was on the right path. I looked at the new defrost thermostat and they had different ends on it then the one I just removed, and I remember reading what another member did, and that was to cut off the connecting caps, strip the wires , use electrical tape to join them and use a crimping tool to place the old caps on to the new defrost thermostat .I then inserted the thermostat to the freezer's wiring. Hope that makes sense to everyone. WEll, everything is running great! Thank-You Part Select, you saved me lots of money!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires... Put a thermometer in a glass of water & now runs at 38 degrees.

I have a side by side Amana fridge about 12 years old. One day I noticed everything was not cold anymore. I checked the temp with my infrared thermometer and it was about 70 in the top of the fridge, 40-50 in the bottom, and freezer was the same! So after pulling out the two baskets in the bottom of the freezer and the side rails that hold the baskets, I used a 1/4 nut driver to remove the back lower panel. After looking at the electrical schematic on the back of the fridge, I jumpered around the defrost thermostat, a little cylinder with two wires coming out of it. Bingo, the fan turned on. Well after a few days of running fine with it jumpered my new one arrived. I never really tested my old one with a meter so I did that and it tested fine, so I plugged the old one back in and it worked fine for a few days. Then one day I noticed that fan wasn't running again so I just put the new one in. I had to cut one of the connectors off as it was female instead of male and crimp cap it together, but besides that it went fine. So after connecting it I noticed the fan motor was buzzing but not spinning. I wiggled wires around and determined the connector going into the fan motor had to be a certain way to make the connection. I unplugged it, it wasn't corroded or anything but if pulled down on, it would not make connection. So pulling up on the connector proved that it would make good connection, so a ziptie keeping the wires tight in the up direction proved to be the solution. I'm pretty sure my old defrost thermostat was not the problem. So that's my story. Hope it helped.

I had to cut a groove in the bushing to put the elec. wires through it, & then just remove the hinge, put the bushing in & replace the hing.

remove ice maker vent and back piece. Unclip defrost thermostat and unplug. Plug new thermostat in and clip to element, reattach back piece, vent and ice maker. Is a tight fit getting icemaker out, there are 3 screws 2 on top and one on bottom.

Removed the cover to the timer, 2 nut screws. Easy. Then emptied freezer, and took off back plate with nut driver. Replaced thermostat. 2 wire plugs that were easy to complete. Left back off, let thermostat normalize temperature, then switched to defrost setting. Worked like a charm.

Used information on internet as to how to check and repair unit. Due to high cost to have repair come to let me know it was broken, being handy with repairs, I took it upon myself to check the timer and therm, ordered the parts from this site , got them within 5 days, took about 40 minutes to use simple tools to remove and replace the timer and therm, used hair dryer to defrost coil unit and turned unit on, lit has been working well since then, about 2 weeks since repair. Saved lots on repair/labor cost and parts cost. Well satisfied, will use this product company again. I WAS AMAZED HOW EASY REPAIR WAS, WIFE HAPPY NOW!

It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigerator is still too wide but it's colder.

I replaced the run capacitor wich is located near the compressor, i first turned power off to fridge than remuved capacitor checked for continuity and the capacitor was the problem thanks

Watched the video you posted with the part and getting the gasket to fit like he did was not as easy as he made it look. Took me a few hours and before I was done the lights went out from a power failure but I was able to finish because the drill was battery operated. I may have saved money doing it myself but not time.

Removed refrigerator door. Removed 3 screws. Replaced old ice maker with new ice maker. Put in 3 screws. Ice maker working great.

Removed the slide out bin and then removed the many screws that held the inner panel to the outer insulated door panel. Removed the gasket. Melted the ice and dried the fiberglass perimeter insulation in the door panel. Placed the gasket in position on the door that was lying on the table. Replaced the inner panel screws. Put everything back together.

THERE IS A PROBLEM NOW. THE GASKET DOES NOT MAKE CONTACT ALONG THE TOP EDGE AND AIR LEAKS INTO FREEZER. SIDES AND BOTTOM ARE OK. DO NOT KNOW WHAT TO DO NEXT.