KBRA22KRSS01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- PAUL J from LANCASTER, NY
- Parts Used:
- WPW10128551, WP2169142
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Fan motor noise
Followed the demo film on line.
Good instructions
Good instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from HUNTINGTN BCH, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Difficulty removing old switch.
Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from WATERVILLE, MN
- Parts Used:
- WP67006878
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Clean the glass and asked my wife to install the glass. She is less likely to brake the glass
Removed the plastic frame, washed the frame and fridge, set new glass into the frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Alliance, NE
- Parts Used:
- WPW10568041
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Crisper frame broke
Watched the video that was attached with part invoice. Video made it easy to perform since I’ve never done this task before.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from AUBURN, CA
- Parts Used:
- W11396033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Refer lights not working, there are two lights and neither worked. Decided the switch was the problem.
The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from BUFFALO, MN
- Parts Used:
- WP67003426
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Lower freezer iced over compartment, upper refrigerator warming up.
Unplugged unit. Allowed to melt ice and drain overnight. Removed ice maker. Removed back panel to freezer/coil section. Cut wires to defrost thermostat and removed. Installed new defrost thermostat and wire nutted two wires. Reinstalled back panel and ice maker. Plugged unit back in. (I unplugged defrost heater and used ohm meter to verify that the defrost heater had continuity, and did not have to be replaced).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from VINTON, VA
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Ice maker leaked
Removed refrigerator door. Removed 3 screws. Replaced old ice maker with new ice maker. Put in 3 screws. Ice maker working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from ZUNI, NM
- Parts Used:
- W10613606
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Refrigerator went out during blackout.
Installed the part, fan turned on, lights on, however, the freezer did not get cold and refrigerator is not working at all. Need advice!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Red Banks, MS
- Parts Used:
- 12002497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Freezer Drawer Gear
Checked Video online. Had to remove the 2 snap on track/gear covers. Pry out the gear with screwdriver and the gear bearing unit. Align the flat side of the bearing unit and snap in. Position the cut teeth on the gear to match original and snap into the bearing. Insert the connecting rod into the long shaft gear and then push back into the short shaft gear. The video said to remove the drawer front but I did not and don't see that it necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lionel from Watertown, NY
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Icemaker not installed in refrigerator
I followed the instructions for the installation of the icemaker and its connection to the house water supply.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERMAN from PENN YAN, NY
- Parts Used:
- WP67003903
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Noisy Damper
Very simple, turned off power-removed cover-unite is held with clips-removed wires-and instaled new unite ,reversing removal process. Great service. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PHOENIX, AZ
- Parts Used:
- W11613295
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The refrigerator was working for just 1 minute and breaks, I discovered that the fan was not working , I understood that there wsa something wrong with the condenser fan motor. I just order a new one.
The installation video for condenser fan motor helped a lot to know how to disconnect the old fan motor and connect the new one. So easy just know how to remove and put back the fan gently, observe carefully where is the center and the connector position; 15 min after everything was done and the unit works well to date.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carlton from CHICAGO, IL
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light out.
Popped out the old switch and replaced it with the one dying
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DIANE from WEST PALM BCH, FL
- Parts Used:
- WP67001716
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
I had no problem
Just take the crisper out and just put it in the hall access
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from PORT JERVIS, NY
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No problems
Just plugged it in
Was this instruction helpful to you?
Thank you for voting!