KORU06RSSS00 KitchenAid Refrigerator - Instructions

I would never attempt an appliance repair but after watching the video instructions for installing this part I decided to give it a try even though I'm dangerous with a screwdriver. After retrieving a nutdriver from my $39 handy dandy tool set, it was a piece of cake. Upper hinge cover, hinge, door removal, comes off in a matter of minutes. Only problem surfaced when I went to install my new cam in the lower hinge. It didn't fit. It was actually for the upper door hinge. I reinstalled the lower plastic piece (whatever it's called), tightened it down, put the door back on (you can do it yourself if it's the refrig. side) and popping sound was gone. I guess the bottom hinge plastic piece was probably loose but you can't tighten it unless you remove the door. I now have a upper door cam in my drawer ready when it fails and will replace it without hesitation.

Removed the nut holding the plastic cover plate at the top of the door. Removed the 3 nuts holding the latch to the fridge. Lifted the door up and laid it on its' side. Removed the nut holding the door cam and replaced it with the new one. removed the nut holding the lower door cam and replaced it. Put a little vaseline on both cams and re-in-stalled the door. Took less than 15 minutes and the door is like new. Watching the video on the web site was perfect.

Pulled out the Fridge. Removed the plug. Removed the back panel screws with nut driver. Vacuumed the coils & fan area. Disconnected the fan cable. Used a socket and thumb ratchet to remove the 3 mounting screws from its sheet metal bracket. Slid the old fan assembly out. Assembled the new Fan blade onto the new motor shaft and attached the adapter cable to the fan connector. Slid the assembly into place and reattached with 3 screws using socket and thumb ratchet. Connected adapter cable to fridge harness and plugged in the power cord to test the fan. With it working Quietly and knowing the the problem was solved, the back panel was reattached.

changed bulb

All you need is nut driver. Top hinge has 3 screws. Once you remove the screws, lift door. It is light. I place door of my sofa. I removed screws and pried the cam insert with a spatula. You can also you flat screwdriver. I also replace the other piece located at bottom of refrigerator. Now place door back onto metal rest. May need someone near floor to guide you. Once on the rest, close door and replace top screws. Forgot to mention that I emptied door shelves before removing door.

Removed door, removed both upper and lower cam and replaced, applied small amount of vasoline and replaced the door. The entire repair took less than 5 minutes. Door works great. When replacing the cam you need to replace both the upper and lower cam. When you order the parts, the upper cam is on the door schematic and the lower cam is on the refrigerator body schematic. I originally only ordered the upper cam.

Remove all items from door. Remove bolt holding plastic cover on top hinge. Support door and remove 3 bolts holding hinge. Lift door off lower hinge pin. Remove bolt holding both cam assy's and pry the one on the door out with the screwdriver. Replace both with the new cams, place door on lower hinge pin, place upper hinge pin into door, loosely insert the 3 bolts. Align the door, tighten the 3 bolts and replace plastic cap/bolt. Put the food back in the door and you're done. The only nut-driver needed is 5/16" and the screwdriver is only needed to pry out the cam that's located on the door itself.

I watched the film on installing and taking out. Step by step. easy.

Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!

About 7 screws total. ! screw holding side shelf removed. 2 screws holding bottom rear panel removed. 2 screws holding rear panel top removed. 2 small screws holding the fan motor bracket. Remove 3 wire connectors from fan motor and then remove plastic fan(pull off) Then just reverse the procedure. As always please make sure unit is unplugged. If there is ice buildup in freezer use a blow dryer to melt and then dry unit. Very easy fix!

Easy fix. Used this a teaching opportunity for my 18 yr old son and had him do all the work. The cams have like little inclines that as the meet close the door with like a over center effect. Empty the door. Just undo the top plate 5/16 screws and lift door off. On bottom of door change the 1 piece lower door closing cam and on the bottom post plate change the door cam. add a little grease and reverse the process to install. later in life my son will know how to make this repair.....easy to do folks.

I unplugged the refrigerator(for safety). Using a 1/4" nut driver I removed 1 screw holding ice tray rack. I then removed the 2 screws holding the lower shroud inside the freezer section. I then removed 1 screw holding cover plate where ice maker would be and disconnected the ground wire from the back panel. I then removed the 2 screws holding the back panel in place. This allowed me to removed back panel from from inside the freezer. I removed the fan blades from evaporator motor by pulling straight away from motor. I was then able to disconnect the power wires and the ground wire from evaporator motor. Using the 1/4" nut driver I removed the 2 screws holding the front motor bracket and removed the evaporator motor from its bracket housing. Using the an electrical cord that i had fashioned with two female spade connectors on each lead of the wire, i connected these to the motor and plugged the male end of the electrical cord into a standard 110v outlet to verify that the motor was in fact the defective component. The motor did not operate so I replaced the evaporator motor with a new motor and put everything back in reverse order. The refrigerator is running like a champ and keeping the refrigerator contents a cool 42 degrees. Thanks PartSelect.com

Removed the refrigerator door (after taking everything out of the shelves). Took the old Lower Door Closing Cam off (it was totally worn down), installed the new one, rehung the door. Rehanging the door took a couple of tries to get it properly aligned. Very easy fix, We thought we had to replace the refrigerator since it is 14 years old, but this fixed the problem completely!

Openned both doors and removed lower grille. Closed doors and placed a piece of wood underneath door. The piece of wood slightly taller so that it supports and lifts the door while I worked. Working at the bottom of the door removed both upper and lower plastic cams and replaced with new ones. Be sure to tighten the single screw that holds down the plastic cam; if you leave them loose they will split/crack because they will move as you operate the door.

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.