KTRS25KGWH02 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- monty from royston, GA
- Parts Used:
- 4396418
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
plastoc piece holding handle broke; could not control amount of ice it made
removed old ice maker; installed new ice maker
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Carol Stream, IL
- Parts Used:
- WPW10348409
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Screws on the door of the dishwasher were very loose.
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from Shreveport, LA
- Parts Used:
- W10833899
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
ice maker quit
tested that water got to inlet valve, but not past it. the rod inside the pump was separated from the plunger. i ordered part. i was quite impressed that i got part within two days. replaced valve. ice maker works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Columbiaville, MI
- Parts Used:
- W11177593
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer seal was broken
Thanks to some reviews we found online about replacing gaskets, ours went very smoothly. One person said to soak the gasket in hot water, which we did til it was very soft. Installed like a breeze. Then, the same person said to tape the door closed after installation, we did that too. The gasket looks like it was professionally installed and we have never done it before. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jack from north wildwood, NJ
- Parts Used:
- 4396418
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
water was running into the bin and making a big chunk of ice in addition to the cubes
removed the old unit and put in the the new one, no other parts were needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Millsboro, DE
- Parts Used:
- WPM0274057, 67007018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
We moved and the movers lost the bottom hinge assembly for the door
Went online and located the right part numbers. When delivery happened I put it together and all is fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cliff from Metairie, LA
- Parts Used:
- WP10097202
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
compressor will not start - when you turn it on - it hums for a few seconds and them you hear a click sound (the overload opens) and the hum stops
be sure the power cable is NOT plugged into an electrical outlet - removed the cover on the bottom rear of the refrigerator - using a flat blade screw driver pry the cover off the side of the compressor - remove the old relay - remove the wires from the old relay and install them on the new relay in the same location - install the new relay on the compressor connections - snap the cover back on the compressor - replace the cover - power the refrigerator on - the compressor should start and run normally
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from clarkston, MI
- Parts Used:
- WP67001255, 4396418
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
3 sets of instructions 2 water valves.
It would have been nice to know which booklet to read and why send to water valves,with out saying something about an extra vavle. After checking holes to see which valve to use the rest of the installation went fine. Most of the time was figureing which set on instructions were for our refrigeator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILLIP from SUN CITY CENTER, FL
- Parts Used:
- WP65889-4
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver
Loud, non-rythmic clicking noise shortly after the compressor comes on, continuing for several seconds.
Replaced the "Run Capacitor. The non-rythmic clicking associated with the compressor coming on continues. The problem was obviously not the Run Capacitor". I don't know what to do next. Any suggestion would be appreciated.
Thanks,
Phillip
Thanks,
Phillip
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Danbury, CT
- Parts Used:
- WP12550113Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
Existing Door Gasket Was Leaking and Deformed
I followed instructions, both supplied with gasket, and some I found on-line. Pretty easy - loosen screws holding existing gasket, remove existing gasket, install new one, tighten screws. [TIP - I didn't soak new gasket in hot water before installing - definitely do this to get rid of the "wrinkles" caused by shipping. Throw it in a tub, and let it soak.] The problems I had to iron out were AFTER I installed new gasket. Door alignment shifted, so I loosened all gasket screws, realigned, and then tightened. Then door was not closing (it had dropped for some reason at the handle side), so I had to loosen hinge bolts, push up door, and re-tighten. I had to do this 3 times before door closed right. I also had to heat two sections of the new gasket with blow dryer to smooth gasket. After about two days, the gasket was sealing perfectly. No condensation in fridge, no leaking out bottom. I estimate by putting in a $100 gasket, I saved over $1,500 because my wife was ready to get brand new fridge. Good luck, and be patient if door needs to be realigned. Also - gasket may still have small gaps even after you install and heat it - give it a few days to conform to fridge before trying heat again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from River Edge, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this instruction helpful to you?
Thank you for voting!