KRCA06XPSS00 KitchenAid Refrigerator - Instructions

Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

Fast after a little help from a friend

After removing two rear plastic panels, (very easy). The fan is easily accessable. Two more screws to remove the fan brace and remove three wires from the fan and its out. Reverse the process and its finished. The propellor is not part of the fan motor order and you can remove the old propellor and put on new motor (easy). One step that is not accounted for is the removal of a flexable plastic "nut" on the fan shaft. This piece holds and connects the fan to the fan brace. You will understand this when you compare the new fan with the old and see the plastic "nut" sleeve on the old fan. Simply pull it off and put on new motor shaft (it simply slides on and off the shaft).

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

Unplugged the refrigerator and then unloaded the freezer. removed the panel at the back of the freezer to expose the fan. Carefully unclipped the wiring harness and then removed the fan motor. Swapped the fan from the old motor to the new one (I did use a hair drier to warm the plastic fan to make it easier to remove) and reassembled the fan and panel. Simple and easy, and now the refrigerator works just like new.

Pretty much followed the how to video. Biggest pain was removing the screws to the bracket that houses the motor.

New part was not needed, when I removed lower closing cam the lower part of the closing cam attachment screw had worked it's self lose. So it just needed to be re-torqued. That took care of the problem.

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

My husband watched the video on the repair and followed it step by step...works like a charm! The repair shop wanted 299.55 to fix it - the part was 79.00....big savings by doing it ourselves.

I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.

Replacing the door closing cams, starts with emptying the door of all foodstuffs. Remove upper hinge cover. While supporting the door, remove three upper hinge screws with the nutdriver. Lift upper hinge from top and lift door off lower hinge pin. Remove the cam retaining screws on both the bottom of the door and the lower hinge pin. Pry (if needed) the worn cams from their position. Install new cams making sure to line up the screw holes. Re-install screws, tightening just snug. Lift door back onto lower hinge pin. Set upper hinge back in place with screws loosely installed. Check door gap, top to bottom to ensure proper alignment. Tighten upper hinge screws and re-install hinge cover. Check door for proper function.

Remove all items from door. Remove bolt holding plastic cover on top hinge. Support door and remove 3 bolts holding hinge. Lift door off lower hinge pin. Remove bolt holding both cam assy's and pry the one on the door out with the screwdriver. Replace both with the new cams, place door on lower hinge pin, place upper hinge pin into door, loosely insert the 3 bolts. Align the door, tighten the 3 bolts and replace plastic cap/bolt. Put the food back in the door and you're done. The only nut-driver needed is 5/16" and the screwdriver is only needed to pry out the cam that's located on the door itself.

Removed the old cam and put books under the door to hold it up. Follows instructions and really easy