KSSP42QTS02 KitchenAid Refrigerator - Instructions

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

I pushed the lever on the filter located at the bottom of the refrigerator and it popped out.

followed the video provided on website. repair was very simple / straight forward. Once emitter and receiver boards were replaced, issue with ice maker was resolved.

filter has to be removed and attached then inserted into rifrigerator

The bearing & cup assembly was broken and the gears in the drive assy were stripped. Unfortunately I couldn't find anywhere to buy the gears without buying the entire motor assy with the gear box already on it. Cost was up to $85 with shipping but at least it now works fine.

To repair: a 1/4 nut driver will take off screw below ice maker and all you need to do is loosen the 2 screws above the ice maker then push it upward slightly and it will slide off the top 2 screws. Then pull the power connector off from behind the ice maker at the side of the refridge. Then pull straight out and it will slide off the water fill tube. Now with unit out of refridge I took the cover off the front of the ice maker and removed the 3 philip screws. I then pulled the motor/gear assy off from the chassis of the ice maker. I then had to remove the 2 philip screws on the chassis (under the motor/gear assy) to remove the cube maker/element from the chassis. This allowed me to remove the rotating cube spatula bar to replace the filler cup/bearing assy. Then I reinstalled the spatula bar and the 2 philip scews on the chassis to the cube maker/element assy. I then installed the new motor/gear assy to the chassis and installed the 3 remaining philip screws. Put the cover back on the ice maker and inserted assy back into the refridge by first reattaching the power connector and then sliding backward onto the water fill tube and then slipping over the top of the 2 top screws on the refridge. Then I installed the screw below the ice maker and tightened all 3. Presto - repair done in 30 minutes and perfect cubes were spitting out within the hour.

With the freezer door closed, remove 4 screws around the ice maker door assembly. Open the freezer door and remove about a dozen small flat-head screws around the sides of the door that hold the stainless steel cover to the freezer door. No need to remove the very bottom screws if you have something to support the cover with. Remover 4 hex-head screws that hold the ice/water dispenser control pad in place, use tape to secure this pad to the freezer door so you don't have to undue all the electrical connections. Remove two screws that hold the Ice Door Motor & Bracket Assembly in place - disconnect the electrical connection for the assembly. Replace the new assembly in the opposite order it was taken off. Presto - done.

System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.

Used the online video and followed it step by step. Very good instructions on how to perform the repair.

I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.

changed the ice door..& motor changed a few more little thing wile i was in there , no more problem

Easy repair. Remove 2 hex bolts. And remove.Install Bracket and replace 2 hex bolts and reinstall ice maker door to bracket. 10 minute repair.

Replaced the control of the ice maker assembly.

The emitter code: Hold the flap that covers the receiver. (On the left) If the emitter does not stay red, the emitter and receiver are defected.

Replaced the emitter and receiver board

Unplug the refrigerator:

I first removed the ice-maker service door by removing the 2 screws at the top. Next, I removed the 3 screws on the lift side that housed the receiver. It is close, so remove the 1 gold screws on the receiver. This will allow you to separate the switch without any damage. Plug the new receiver in and reverse the process. Put the gold screw in to secure the board. Replace the 3 screws back into the receiver panel.

Remove the 3 screws on the right side. The emitter has 2 gold screws. Remove them so I could separate the switch. Plug the new switch in and replace the 2 gold screws.
Place the 3 screws back into the right side panel.

This process took roughly 30 minutes. After assembly, the ice make was dropping ice in 30 minutes.

There are several large parts places in my area but I saved about $35 by ordering online.
I place my order on Friday morning and the part was in my hands Saturday @ 6: 30 PM the next day.




Oliver of Riverdale, Ga