KBRS22KGBL2 KitchenAid Refrigerator - Instructions

I loosened(but did not remove) the 1/4" sheetmetal screws around the perimeter of the door liner. (they are numerous and they are hidden in the fold of the gasket) I removed the old gasket. With the screws still loose, I installed the new gasket. After insallation I re-tightened the liner screws. Several gaps were noted and eliminated by gently heating the gasket with a hair dryer. (be patient , it takes some time)

Started with internet searches then began with removal of wall plate at back of freezer, pulled power cord first. Found evaporator coil completely frozen over.Went back to internet and searched possible causes. It seemed to me that the auto defrost system may not be functioning properly so I considered possible causes. Defrost thermostat, defrost timer, or possibility heater itself. I chose to go with simple stuff first and thought heater would have a better relibility characteristic. Went to Parts select got part numbers and was able to find part locations on the appliance. So far so good, and knock on wood! Thanks Parts select I spent $50 bucks instead of $1000.

1- Remove food from freezer and store in ice chest
2- Turn off refrigerator
3- Remove freezer drawers, 2 drawers, no fastener
4- Remove freezer slide out drawer front , 2 screws
5- Remove ice cube tray holder, 2 screws
6- De-ice back panel with hair dryer / blower
7- Remove back panel in freezer, 8 screws
8- Defrost refrig coil with hair dryer / blower
9- Unplug Bimetal Thermostat, 2 wires, orang / brn
10- Remove Bimetal Thermostat from coil, 1 clip
11- Install new Bimetal Thermostat
12- Re-assemble, reverse order

I followed the instructions for the installation of the icemaker and its connection to the house water supply.

I sealed the freezer with cardboard and duck tape and kept the door attached (I recycled all the cardboard after I was done). I didn't need to use the hair dryer to remove kinks from the gasket because I couldn't get to the repair for a week and the gasket was in good shape after I took it out of the box.

I almost installed the gasket without removing the plastic door liner (more the twenty small hex screws) but I'm glad I decided to remove it after all. When I removed the plastic liner half of the fiberglass insulation was consumed by a huge block of ice. All these years my freezer had been working harder and wasting more energy than necessary.

I removed all the insulation and replaced it with spray insulation which took longer to allow for the spray foam to cure. The reason I knew what I was doing was because all of you took the time to post your installation experiences. Thank you....

By the way, if you decide to remove the plastic liner for my model, it really helps if someone holds the liner while you attach the first few hex screws. Thank you wife. Also, I'm so glad I had a can of spray insulation in the garage so my wife wouldn't say "how many trips to Home Depot is going to take to finish the job"

Used information on internet as to how to check and repair unit. Due to high cost to have repair come to let me know it was broken, being handy with repairs, I took it upon myself to check the timer and therm, ordered the parts from this site , got them within 5 days, took about 40 minutes to use simple tools to remove and replace the timer and therm, used hair dryer to defrost coil unit and turned unit on, lit has been working well since then, about 2 weeks since repair. Saved lots on repair/labor cost and parts cost. Well satisfied, will use this product company again. I WAS AMAZED HOW EASY REPAIR WAS, WIFE HAPPY NOW!

Removed refrigerator door. Removed 3 screws. Replaced old ice maker with new ice maker. Put in 3 screws. Ice maker working great.

Removed the cover to the timer, 2 nut screws. Easy. Then emptied freezer, and took off back plate with nut driver. Replaced thermostat. 2 wire plugs that were easy to complete. Left back off, let thermostat normalize temperature, then switched to defrost setting. Worked like a charm.

Removed the slide out bin and then removed the many screws that held the inner panel to the outer insulated door panel. Removed the gasket. Melted the ice and dried the fiberglass perimeter insulation in the door panel. Placed the gasket in position on the door that was lying on the table. Replaced the inner panel screws. Put everything back together.

THERE IS A PROBLEM NOW. THE GASKET DOES NOT MAKE CONTACT ALONG THE TOP EDGE AND AIR LEAKS INTO FREEZER. SIDES AND BOTTOM ARE OK. DO NOT KNOW WHAT TO DO NEXT.

Watch video. Very helpful, followed instructions went in fairly easy. Gasket deformed, used hair dryer could not get to set straight. WAIST of TIME and MONEY. I wouldn’t recommended buying one of these twisted gaskets, buy a new fridge which is what I’m doing tomorrow.

I have a side by side Amana fridge about 12 years old. One day I noticed everything was not cold anymore. I checked the temp with my infrared thermometer and it was about 70 in the top of the fridge, 40-50 in the bottom, and freezer was the same! So after pulling out the two baskets in the bottom of the freezer and the side rails that hold the baskets, I used a 1/4 nut driver to remove the back lower panel. After looking at the electrical schematic on the back of the fridge, I jumpered around the defrost thermostat, a little cylinder with two wires coming out of it. Bingo, the fan turned on. Well after a few days of running fine with it jumpered my new one arrived. I never really tested my old one with a meter so I did that and it tested fine, so I plugged the old one back in and it worked fine for a few days. Then one day I noticed that fan wasn't running again so I just put the new one in. I had to cut one of the connectors off as it was female instead of male and crimp cap it together, but besides that it went fine. So after connecting it I noticed the fan motor was buzzing but not spinning. I wiggled wires around and determined the connector going into the fan motor had to be a certain way to make the connection. I unplugged it, it wasn't corroded or anything but if pulled down on, it would not make connection. So pulling up on the connector proved that it would make good connection, so a ziptie keeping the wires tight in the up direction proved to be the solution. I'm pretty sure my old defrost thermostat was not the problem. So that's my story. Hope it helped.

This is easy. Remove lower vent in front of frig to change timer. Unplug and put new one in. . . . 10 Min. To change the thermostat remove food, take off back panel, defrost ice with hairdryer and locate thermostat (to the right above coil) remove old thermostat from connectors and replace with new. One connector needs to be spliced cause it does not match. No problem just use old connector and splice and seal with shrink tubing to prevent moisture from connection. In jersey repair guy charges you 100. 00 Bucks to just walk in the door. . . Forget that. Works fine

It was easy after it was apparent that the run capacitor was plugged into the compressor. This was determined from a parts diagram of the actual model refrigerator. The part was the same but the location on the video was wrong. A large screwdriver was used to unplug the capacitor from the compressor. The temperature range of the refrigerator is still too wide but it's colder.

Watched the video you posted with the part and getting the gasket to fit like he did was not as easy as he made it look. Took me a few hours and before I was done the lights went out from a power failure but I was able to finish because the drill was battery operated. I may have saved money doing it myself but not time.

I had to cut a groove in the bushing to put the elec. wires through it, & then just remove the hinge, put the bushing in & replace the hing.