KSRA22KKBT02 KitchenAid Refrigerator - Instructions

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

One screw inside the refrigerator removed the cover exposing the diffuser assembly. I had to also remove the cover inside the freezer compartment in order to free the diffuser assemble bracket that protruded in from the refrigerator compartment directly on the other side. Once the diffuser was freed, the assembly came off in my hand. The new one just snapped back in place. Done.

remove door pull gasket out put new gasket in replace door

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Removed the back panel on the refrigerator--unplugged the condenser fan motor--removed the motor--placed a small fan to cool the condenser--called parts select--ordered the motor--the motor arrived less than 24 hours after I ordered it--replaced the motor and rear panel on the refrigerator--probably saved more than $200. 00--Very happy with parts select service--plus I had a misunderstanding with my credit card and john at parts select was very helpful --not their fault--excellent company

Open back panel bottom cover (4ea 1/4" metal screws) of appliance and located compressor. A little extra cleaning of all the dust accumulated over coils to allow better airflow. This was a lot more to do than just the relay, I had to elevate the fridge 6" or so to get access to the coils, tight area to get vacuum into. The relay is easy to reach then connected to compressor by contact Pins. Relay was secured by small wire clip, Removed wire clip and relay with Capacitor mounted to top was removed by pulling it straight out (with a little wiggling) and the two wire plug then removed. Needed a small screw driver to release pin locks on the plug. With relay removed it displayed same symptoms as noted on other repairs on the site. Lose insulator material fell out of relay and rattled. (not a good thing).. Before replacing selected the correct relay for this compressor (3 in kit) matches noted in instructions from kit and simply reversed the removal. It took a while for fridge to cool again. All works fine, maybe even a little better. Cleaning helps.

This was a very simple job. Remove the top Hinge bracket, a total of 4 screws, lifted the door off the bottom hinge, removed the bottom hinge set up, 2 screws, replaced it, and attached the new bottom black door cam, lifted the door back onto the bottom hinge and aligned the top hinge, and reinserted the screws, and Ta Da, The door works like a new refrigerator door. 15 to 30 min tops. I did not even have to take the refrigerator items out of there door holder.

First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together

Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that holds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.

I didn't. Don't know how to get to light bulb to change it for this specific model

I FOLLOWED A U TUBE VIDEO. IT WAS ALMOST PERFECT FOR MY SIDE BY SIDE REFRIGERATOR.