KSRS25CKSS01 KitchenAid Refrigerator - Instructions

Removed cardboard back from refrig. Found source of smell/burn. Removed part. Ordered several replacement parts as the diagram was not clear as to which part would be needed. New parts arrived, matched with old. Cleaned carbon from contacts, installed new part. Cleaned dust from refrigeration coils, installed back. Returned unused parts.

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

1. Removed Ice cube bin. 2. Removed the 4 screws holding dispenser bracket in place. 3.Unplugged electrical connector for motor and removed the unit. 4. Removed the coupler,wiring connections and three screws holding dispenser motor to mounting bracket. 5.Installed new dispenser motor onto bracket, put on coupler and connected wiring to motor. 6. Installed newly assembled unit put ice bin back into place. Dispenser works great.

the parts sent included two replacement kits which at first was confusing. I determined that I only needed the one with the black tubing for my Kenmore refrig. Turned off water supply and vacuumed up all the dust bunnys behind refrig. Removed bottom grate on refrig where black tubing attaches at the other end. Released water left in tubing at dispenser. I did not have to remove the front panel. Removed one screw attaching the nozzle to the dispenser. Decoupled tubing at the far end, more water came out here too. Pulled out upper end of tubing a couple of inches and snipped off. Attached tubing to new tubing with thin wire (as others here recommended) and had my husband pull at far end while I pushed slowly at the dispenser end. Once through reattached screw at top and recoupled at the bottom. Mission accomplished!

First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left handed threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.

Remove the kick panel and simply turn the filter counter clockwise and it slips right out.Water shuts off when filter is removed.After new filter is installed be sure to bleed line thru the water outlet in door to clear air in system.When first water is bled the water will continue to run until line drains. Then comes the air.Bleed until water is clear.Its an easy job and can save you$$$$$.Ray Palm Bch Fl.

insert and turn!

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Ice Maker would seem like it was the valve was leaking and Ice would build up at the rear of tray.
After listening to it cycle, (drop ice and fill) valve would open up again about 20 minutes later.
Over flowed and iceberg would form at rear.
Replaced icemaker unit and works fine now.

It was really easy to do. The water filter is in the front of the refrigerator. Less than 30 seconds. I am very happy with PartSelect. I bought parts for my dryer too. New lint filter, timer knob and door handle. Parts arrive immediately. I am sure I will be back to PartSelect.com.

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.

It was easy, I followed the instructions on the paper and it went well.

I first removed the ice bin from freezer. There were four nut screws on back of ice bin cover that I removed with a screw driver, giving me access to the deflector. The deflector has two prongs that attach it securely to the ice bin, I used a phylips head screw driver to release the prongs from the deflector. I installed the new deflector by placing it through the bottom portion of deflector area, using the phyllips screw driver I engaged the prongs of the deflector into slots on ice bin. There was a hook on the back side of the deflector that went over a metal rod that controls the ice cube release. Then replace front cover of ice bin with the four nut screws and returned it to the ice maker location.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

changed the starter connected to the compressor