KSRF36DTX10 KitchenAid Refrigerator - Instructions

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) remove the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC

Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.

Followed on line video

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Fairly straight forward remove and replace. Tight limitations made it a little difficult but universal joint for socket set allow the best access to the screw that held the lever in place. Replacing the spigot onto the water line was a concern. The fit was so tight you must take care not to damage the plastic line.

Unplug refrigerator. 1. Using a thin screwdriver, slowly and carefully pry the front panel off that is around the ice and water dispensers starting at the bottom. Once the bottom side has been popped off, carefully lift up on the panel until the top tabs pop loose. 2. Remove the next panel (5 screws) which holds the light and two switches with a screwdriver or nut driver. I then taped it over to the side onto the freezer handle to keep it out of the way. I preferred not to unplug anything. 3. Remove the door mechanism with a nut driver. The same screw holds the water spout and door mechanism together. 4. Reverse the steps and you're done! I now have a silent ice door.

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.

Very easy to order from parts select. Took seconds to replace.

I took out the ice bin and in the back where the auger meets the ice bin I had to replace the small plastic piece to hold the auger in place when using the automatic ice maker. It was an easy fix.

ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!