KBSN708MPS01 KitchenAid Refrigerator - Instructions

Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.

took off old filter put in new - simple

I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.

Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.

Popped out the old filter from the refrigerator bottom. Removed new filter from the box and pulled off the end caps. Put the end cap on the new filter, aligned the filter( it will only go in one way) with alignment slides and pushed the filter in until I heard it (click) into place. Pushed in the water dispenser tab for a few seconds, but nothing happened. So I waited until the next day and pushed the dispenser in and water flowed out. Repeated this process until the water ran clear. Turned the ice maker back on and a few hours later ice was popping out. Wife's happy, I'm a hero!

Pulled out the old filter with the push of a button, removed filter cover from frig, took covers off the end of new filter and pushed it into the slot replaced cover. Job done--1 minute.

After years of using a flash light to check the contents of my refrigerator, I decided to try to fix the problem myself. Replacing the light switch was very easy. The directions were straight forward and I'm sorry I waited so long to tackle the problem.

Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!

It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.

I watched the on line you tube video on how to DIY. The putty knife worked to pop out the switch. I used the standar screwdriver to unplug the switch from the wire harness. Then plug in the new switch and pop it back in to the roof of the freezer. Tip: watch out when ordering the new switch - the freezer switch is different than the refrigerator switch. The freezer has three prongs. The fridge has two. I initially ordered the wrong part and added a week to the repair time and had to pay shipping to return the first switch.

Completely on my own. Neither the owner's manual nor the instructions with the filter are of any use.A two or three panel series of diagrams with description of the process in English could make it simple. The release and reattachment of the filter are a bit difficult and need to be described as such.

The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.

Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.

Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.

Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in