KBBR306ESS06 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Violet from Aurora, IL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replaced
It was very easy just popped the old one out the new one popped right back in done in about One min .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Salem, AR
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter light showed we needed to change it
only tools needed were my husbands hands. easily removed old filter and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Irvine, CA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty filter indicator
simple twist the existing filter and pull, remove puller cap and place on new filter , pushed in and twist to lock. Reset filter indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FREDERICK from PINELLAS APRK, FL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
Replace water filter
Completely on my own. Neither the owner's manual nor the instructions with the filter are of any use.A two or three panel series of diagrams with description of the process in English could make it simple. The release and reattachment of the filter are a bit difficult and need to be described as such.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Bourbonnais, IL
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch broke
Pulled out old switch with needle nose pliers, unplugged old switch and plugged in the new one and snapped back into place. Very easy to repair. Took less than 10 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from The Villages, FL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed replacement
The repair (really replacement) took less than 2 minutes. You press a button to pop out the old filter and stick the new one in. Easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth from Katy, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no problem, just needed to change the filter
Removed the old one and installed the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- D'Joane from Union City, GA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water Filter Needed To Be Replaced.
Removed old water filter by simply twisting the the cap that houses it at the bottom of the refrigerator and replaced with new water filter. No fuss, no muss! Very impressed. Also, I was quite pleased to have received the water filter that was designed specifically for the whirlpool model that I own. I expected to receive some generic-type model based upon the reasonable price that I paid. Kudos to partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Joliet, IL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter replacement
Just had to take the old one out and put the new one in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bonnie from Redwood City, CA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Switch Broke
Super simplet to fix. Popped out broken light switch and unplugged it and replaced with new switch. Received the part one day after ordering it from your company--AWESOME SERVICE AND TURNAROUND TIME!!! Saved at least $100 plus in repair costs/trip charge for something we were able to do. Great experience and would order from your company again. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Raleigh, NC
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter needed to be replaced
Pulled out the old filter with the push of a button, removed filter cover from frig, took covers off the end of new filter and pushed it into the slot replaced cover. Job done--1 minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Francesville, IN
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken light switch
Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Duluth, GA
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
While closing the door, I somehow cracked off the light switch button.
Popped out the old one......plugged in the new one and popped it back into place. My wife was happy in have light again in the fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Avila Beach, CA
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
broken spring in the light switch in refer
Initially thought I could repair switch, but then discovered spring was broken. Ordered the new switch (Parts Select is very efficient - received switch in 3 days). Was encouraged by the posts regarding the switch installation. I had some difficulty removing the old switch. Used a pocket knife to ease the switch out of the hole to reveal the clip/spring. After noting the clip/spring location I used a small flat-blade screwdriver to release the clip. Even though I released the "molded" clip/spring(be sure to note where the spring is on the new switch and release it on the switch it was tight in the hole and had to use pliers to carefully remove the old switch. After removing the old switch, used pliers to gently remove the wire leads. Then install the leads on the new switch. Note the orientation for replacing the switch and gently feed the connecting wires into the hole so they won't kink or prevent the switch from entering the hole. Install the switch noting the clip/spring location and the orientation of the lever that the door closes on to turn off the light. Be sure to put it in without binding at an angle. Thanks to Parts Select for this service! I'll definitely be back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ann from gastonia, NC
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
time for filter change
Tried to remove filter with no success, there were no instructions in the package. "googled" how to install whirlpool filter and found how to do it.
Was this instruction helpful to you?
Thank you for voting!