KBRC36MHS00 KitchenAid Refrigerator - Instructions

Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

Broken plastic part in motor assembly. Very simple to replace. Sears wanted $322.00!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anything with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.

Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.

Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.

Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!