KRFC300ESS11 KitchenAid Refrigerator - Instructions

had to remove shelving, crisper's, then unscrewed end cap. lifted it off set pin. and reversed for reinstallation. reefer door is reversed which makes it prone to close on crisper if not fully closed

No tools needed. Snapped right into place, easy as could be.

This is a simple repair, the gasket is pressed into a groove in the door and only needs to be eased out (pulled) by hand and the new gasket pressed back into place by hand. Starting the installation in one upper corner to make alignment easy. The side of the gasket with the table face center. For this model remember the doors are not symmetrical and the gaskets are a different size for each door. The gaskets come folded which puts a kink in the gasket. I set them out in the warm sun to straighten out before installing.

I followed the video provided by Part Select. I also let the refrigerator stay unplugged overnight with all the doors open. This p-trap kit has fixed the leaks out of the front of the refrigerator. There is no ice build-up in the freezer. Perfect!

I'd been looking a broken plastic for 3 years. Googled Partselect on a whim and one week later a new drawer and lid arrived at my door. 10 minutes later the refridgerator was like new again.

Actually shouldn't you have included installation instructions with the product?
I had to search for installation instructions on Utube or the job would have ended in another cracked crisper frame.

Remove crisper and take off white front piece from old crisper and add to new one. Replace in refrigerator.

The instructions in the package were not helpful. They wanted me to cut the wiring harness and described where to cut based on the wire colors. My wires were not the same color! I removed the light mechanism using a combination of a screwdriver, putty knife, and plain old muscle with my fingers! The wiring harness unplugged easily and the new one inserted. It was easy to push the whole assembly back into the door. I spent more time looking for something to cut the wiring harness with (and never did find it) than the whole job actually took without needing to cut anything!

I have to say this was the smoothest repair ever! It was easy to find on the site, ordering was easy, part came, snapped off, snapped on new drawer, FINISHED! Thank you!

First, turn off the refrigerator so the open door alarm doesn't drive you crazy while you are working with the refrigerator doors open! Then, remove both crisper drawers, remove deli drawer, remove deli cover from two pins (one was already broken), remove the bottom glass shelf and the plastic glass support. None of this requires any tools, all just slide or lift out. Then, using a nut driver remove the two screws holding the drawer slide from the pantry end cap. You access one of the screws from an opening while the slide is all the way in. This is where I needed needle nose pliers to remove the screw from the opening after it was unscrewed - if your nut driver is magnetic you won't need the pliers. To access the second screw, pull the slide all of the way out. Then you remove the broken end cap by unscrewing 3 screws with the nut driver. Once the screws are removed, you lift up on the front of the end cap to loosen it from a catch on the inside and then pull the end cap out. Install the new end cap by sliding the two tabs into the back of the refrigerator and then pushing down on the end cap to set it in the catch. Now replace the screws, re-attach the slide with the two screws, reinstall the glass and the drawers and then reinstall the drawer cover by slipping it into the pins on each side (be careful when depressing the pins, do it gently or they may break off). Turn the refrigerator back on. You are done These instructions make it sound much more difficult than it actually is, it takes as long to remove and replace the drawers and it does to do the actual installation of the end cap..

Opened package. Washed divider. Dropped in place (where indicated by marks) in drawer. Took a nap.

Popped out the old switch and replaced it with the one dying

pull out old gasket and pushed in new one

Pushed it in just as the old one came off and broke. Took 10 seconds. Push and play!!!!

The Condenser Fan Motor was already removed due to searching for the problem. The new fan motor looked different from the original but I felt very comfortable that Part Select had sent me the new part showing original part number changing numbers over the years. Simply placed the fan blades onto the new motor lined up 2 of the holes placed screws and tightened then plugged the wire ribbon into the Condensor Fan Motor, plugged in the Refridgerator and it worked beautifully.

The instruction video on the Part Select Web Site made it so incredibly easy to install. Installation took under 3 minutes!