KRFF302EBS06 KitchenAid Refrigerator - Instructions

Remove lower freezer door from mounting frame (4 screws). Remove inner shelving and shelving brackets, Total of six screws, three on each side on lower brackets and 4 screws, 2 on each side on upper brackets. Remove ice cube maker (4 screws). Remove thermometer frame from back cover and slide thermometer out of frame. Remove 4 screws from back cover and remove cover. Slide thermometer through hole in back cover. Remove 4 screws from evaporator motor housing. Gently pull plastic fan off of motor shaft. Remove motor from housing and install new motor. Reinstall all parts in the order removed.

Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!

Received gasket. Checked color and size. Because this unit is 33 inches wide one door is 3 inches narrower than the other. Removed shelves from door to provide more room to work. Took 15 seconds to pull out old seal and 1 minute to install the new one. Checked to make sure center sealing flap were on the center side of door. Started in upper corners, worked my way around the perimeter pressing in in with my fingers.
Took longer to R&R and wash shelves than to replace door seal.
VERY EASY

Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Snapped on the new toe grille.

Caused the shelf on my fridge to break a ladder hook. I didn't even know where to begin looking for an Amana refrigerator shelf mount bracket, but luckily found this website from a Google search. The part was super easy to find, arrived in two days, and was a snap to install. What did people do before the internet?

Take everything off the top self, lift the self install the new part ,put self back in place and then install the drawers again. Took minutes.

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

My unit was a bottom mounted freezer, the door assembly and side out rack unit took more time then the repair. Once you take the back panel off it is just a matter of unplugging and two screws. Easier to pull fan mounting housing out to replace motor. Be careful its all plastic, pot off fan blades off shaft, pot out old motor, pot in new motor, slide fan blades back on shaft, make sure you get the mounting housing behind the duck that goes up to your refrigerator section, two screws and plug in connections and your done. Put back panel, rack and door assembly back in and you are friggen again, once you plug it in of course.

I got really tired of taking food out covered in icicles and stabbing a huge block of ice out of the bottom. Turns out all he needed was a little wheel with cogs and I looked up the sticker model number on this site and clicked the part of the fridge. So simple, wish I would’ve done it sooner.

knelt down, positioned replacement kickplate; popped into place, stood up!

took longer to open the box and peel bubble wrap off item than to replace it!

Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max

backout one screw, push mullion up and free from upper and lower slotted tabs, disconnect one electrical connector. Reverse the steps to reinstall. Literally took 2 minutes.

I left this broken rail hang off my refrigerator for almost a year I finally decided to investigate the possibility of ordering the part on line. I found the part on line in minutes and when I received the part it literally took me 3 minutes to install.