KBSN708MPA00 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Eugine from San Antonio, TX
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Water Filter
Peice of pie
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pepperell, MA
- Parts Used:
- W11291138
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Broken light switch
Installing the switch was a breeze, the tough part was removing the old switch. I watched a video on the PartSelect website which showed how to remove and reinstall the switch. I attempted to remove the switch the same way that they showed on the video, but the problem was my switch was surrounded with foam insulation which was stuck to the old switch. I attempted to pull out the switch but was not able to extricate the switch. Finally, I called a friend who works with these switches and he cut away the foam insulation and removed the switch. Being the handyman that I am, I was able to reinstall the new switch. Hope this helps anyone with an Amana refrigerator that has the light switch on the side wall instead of in the light console like the video showed. Don't be afraid to cut away the foam on the right and left sides and the bottom. Don't cut away at the top, because that is where the wire connections are located and you might cut those off and then you'll be ordering more parts. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eugene from Bellevue, WA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
water not dispensing from refrigerator
Popped out the old filter from the refrigerator bottom. Removed new filter from the box and pulled off the end caps. Put the end cap on the new filter, aligned the filter( it will only go in one way) with alignment slides and pushed the filter in until I heard it (click) into place. Pushed in the water dispenser tab for a few seconds, but nothing happened. So I waited until the next day and pushed the dispenser in and water flowed out. Repeated this process until the water ran clear. Turned the ice maker back on and a few hours later ice was popping out. Wife's happy, I'm a hero!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melodie from Gouverneur, NY
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light switch was broken off.
Purchased the new light switch, used a butter knife to pop the old one out, used the pliers to pull the wires off the metal tabs, replaced the new one with no problem. Took about under 1 minute. Lights are now all working.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgar from Kokomo, IN
- Parts Used:
- W11291138
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch that turns light on in refridge broke
watched the video how to remove, and did it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Griffin, GA
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door light switch broken
It took less that 30 seconds to pop out the old one and less that 30 seconds to install the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathryn from Salem, AR
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter light showed we needed to change it
only tools needed were my husbands hands. easily removed old filter and replaced with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mike from barnsdall, OK
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace water filter on rerigerator
push button take old one off put cap on new one,push it back in.easiest thing ever.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julie from Racine, WI
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new water filter.
popped out the old one and popped in the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Violet from Aurora, IL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water filter needed replaced
It was very easy just popped the old one out the new one popped right back in done in about One min .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Joliet, IL
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter replacement
Just had to take the old one out and put the new one in. No problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Irvine, CA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dirty filter indicator
simple twist the existing filter and pull, remove puller cap and place on new filter , pushed in and twist to lock. Reset filter indicator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michalynn from Powder Springs, GA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light switch broken off by container in freezer
Pried out the old switch with small screwdriver, popped in the new one and tah-dah!! ..the light came on. While I was at it, I cleaned out the freezer :). I cannot begin to imagine what a repairman would have charged for this.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Boynton Beach, FL
- Parts Used:
- WP2188820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer temperature too cold
Temperature in freezer too cold. Temperature display showed higher temperature than actual which caused the freezer to continually run. Thermister is found behind a white box on wall in freezer. Unscrew the box from wall and easily disconnect the thermistor clamp. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Francesville, IN
- Parts Used:
- W11291138
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken light switch
Used the butter knife to pry the old switch out, it is a snap in switch so there is a small keeper on the bottom that needs to be pushed in to pop the switch out. Un hooked wires by pulling them off of the terminals (won't shock you) and put them on the new switch and popped it in
Was this instruction helpful to you?
Thank you for voting!