KFCS22EVMS KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Steven from Clinton Corners, NY
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replaced Ice Maker
Followed the online PartSelect video instructions and it was very helpful. The ice maker has to cycle through before it starts making ice so don't be alarmed when nothing happens when you first hook it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from Noank, CT
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacing filter
Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackson from Leesburg, VA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Replaced leaking ice maker after minor screwup!
Old ice maker leaking water and produced ice cubes with black inclusions. First, I removed old ice maker per video instructions. Transferred electrical cable, cover, and bail to new ice maker. First installation failed because I failed to make sure water tube correctly enter back of ice maker. No ice. Initially thought electrical cable wasn't firmly in place. Then I noticed frozen water dripping down back of freezer. A clue! Removed ice maker and reinstalled making sure water tube went through the hole in back of ice maker. Now the new ice maker works beautifully!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from Indianapolis, IN
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice Maker Leaked Creating an Ice block
Merely remove the front bottom screw that attached the ice maker to the refrigerator
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Lift the ice maker gently off of the 2 top screws
Unplug the icemaker wiring harness from the back of the refrigerator, and remove
Snap off the end of the maker and remove the keeper for the wire arm
Remove the wire arm and install on new maker
Unplug the wiring harness from the old maker and plug into the new one
Plug the harness into the refrigerator, slip the new maker over the top screws, with the water feed tube inserted into the maker
Install bottom screw into the bracket that holds it in place.
This took less than 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Las Cruces, NM
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
difficulty unplugging the power pigtail
Just kept working on it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from LAGUNA HILLS, CA
- Parts Used:
- W10884390
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Ice Maker Not operationl
Have part need instructions to remove old and install new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from ST CLR SHORES, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
needed to replace water filter
unscrewed old filter, screwed in new....good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Charleston, SC
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Quit making ice
Loosen the screws on the sidewall (don't take them all the way out and drop them on the floor as I did) and remove the screw from the bottom bracket. Change out the electrical wires and the wire level sensor that does not come with the new unit. Put the new one in place and give it some time to cool down and make ice ( don't be impatient like I was and think the new unit was bad or that you replaced the wrong part)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEN from FOUNTAIN HILLS, AZ
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Original ice maker was leaking
There are 3 screws holding the icemaker in place. After removing the ice bucket, I removed the screws, then twisted the unit to gain access to the power plug. The plug is held in place by a plastic flap which is part of the connector. It has to be pushed down to remove the connector. The new unit went in perfectly and performed flawlessly for 3 days until the compressor blew out! After feeling some sense of accomplishment having fixed the icemaker, I learned that my neglecting to clean the vent grill in the front of the refrigerator had caused its demise. Don't forget to clean the dust out of the vents!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James R. from Laguna Beach, CA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
My ice maker wouldn't make ice. The heaters shorted out and fried the wiring and little motor.
Saw many photos on the Internet that looked like my ice maker, but they were different. I put in my Refrigerator model No. and found my exact replacement ice maker right away. I was a little cautious, because the new one didn't include the wiring harness, or the plastic cover. I took the chance and ordered it. Super fast delivery, a Day or 2 at most. Everything went smoothly, and after the new one was in, I crossed my fingers until the timer kicked in, and I started hearing ice cubes falling in the tray about 3 hours later. Success! I had been having problems with the ice maker almost from the beginning. Hopefully, the replacement will last longer. I will say that this Maytag Fridge. is the absolute worst kitchen appliance I've ever owned in my 47 years of house keeping! The defroster went in the freezer a couple of months after the Warranty ended, and it cost me $375.00 to have a Tech, come in to repair. I got away easy this time, buying the ice maker for $135.00 and being able to do the work myself.
Jim
Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Oak Hill, VA
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice Maker Stopped Working
This was a very easy fix. I took the old ice maker out, including the electrical harness. Switched the harness and stop bar to the new ice maker on my bench, then installed the new assembly. Ice initially had some hollow cubes. I checked the ice maker for level. But it was fine. Thought it might be moving too fast. But it seems to have cleared up. Perhaps it took some time to completely cool down.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Hampstead, NH
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
The old unit had teflon flaking off into the ice
First i used a nut driver to remove the bottom screw, the unclipped the two top clips by leaningthe bottom of the unit outwards. I used a mirror to see the two top clips as i could not see inside. Then i removed the wiring harness from the refrigerator. The unit came right out, i transerred the needed parts, and re-installed. Not too bad - about 45 mins. It works great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Gainesville, TX
- Parts Used:
- D7824706Q
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water leaked into ice bin causing big ice chunks
I disconnected power, turned off water supply, removed three hexhead screws, disconnected wiring harness plug, then reversed procedure. New icemaker seens to be a little slower in making cubes. However, the cubes are clean, perfect shape and THEY DO NOT CONTAIN ANY OF THE BLACK COATING AS THE OLD ICE MAKER CAUSED. THIS WAS A FAIRLY SIMPLE TASK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lake Worth, FL
- Parts Used:
- D7824706Q
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Simple to install -
Removed old icemaker by removing two hex screws and one phillip's head screw.
Disconnected power connection to refrigerator.
Removed power connection harness and ice level sensor arm/levor and cover from old ice maker and installed on new ice maker.
Re-installed in refrigerator. It was simple on this model.
Disconnected power connection to refrigerator.
Removed power connection harness and ice level sensor arm/levor and cover from old ice maker and installed on new ice maker.
Re-installed in refrigerator. It was simple on this model.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacob from Garland, TX
- Parts Used:
- D7824706Q
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Wouldn't make ice
unscrewed the 3 nuts, took off the electrical connection. Then put new one on. One problem, the ice maker had a hole on the side for the hose, mine needed one in the back. I used tape to hold it in place going over the part that was in the wrong place.
Was this instruction helpful to you?
Thank you for voting!