KRFF305EBS06 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Traverse City, MI
- Parts Used:
- WPW10655368
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Drip pan in the back bottom was cracked during shipping and leaked
We had periodic leaks from under the Unit from new, could never figure out where it was coming from. Finally as it began to cause damage to surrounding cabinets, we took the back off and found the multiple cracks in the drip pan. Someone had hand trucked it from the wrong side! It was difficult to figure out the fan removal (it sits in the pan) but push the top forward and pull the bottom back and the fan came out. Then the pan was simple to remove / replace, by reversing the removal procedure, the fan was re installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Longmont, CO
- Parts Used:
- WPW10594329
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Annoying sound from the fan control motor
Removed the grill and control cover in the top middle of the main compartment, removed the control, unplugged it and put in the new one. The thing that took the longest was figuring out that this was the part that needed replacing. The fridge is less than two years old and about 6 months ago the control started making these odd noises. Now it's quiet. Ah peace!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leo from Salem, SC
- Parts Used:
- WP2300868
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Had to replace a hose connector at the base of my refrig/frreezer
Perhaps a helpful hint:
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.
LG
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from STATEN ISLAND, NY
- Parts Used:
- W10316760
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Refrigerator would ice up around the condenser and through out the air vents. Stopping all air flow in the refrigerator. If you defrosted the refrigerator it would work for about 24 hours then ice up again.
Unplugged and empty refrigerator, completely defrosted refrigerator using a hair dryer to speed up the defrosting, put a lot of towels on the floor to soak up the water when the ice melts. Removed all refrigerator racks and drawers, then remove the white plastic and styrofoam condenser cover. You will then see the thermistor, cut the two small wires connecting the thermistor to the harness leave yourself as mush wire as possible. Splice in the new thermistor and put the refrigerator back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from St. Geogre Island, FL
- Parts Used:
- WP12568001
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Latch was broken on the filter cover and would not hold the filter in place.
Ordered a new filter cover, received in 2 days and installed it in about 5 minutes. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
My original gaskets for the fridge and freezer doors seemed to have lost their magnetic hold
I opened the freezer door and peeled out the freezer gasket, inserted the new gasket, and closed the door. I repeated this same process for each of the French doors on the refrigerator. This was very easy to do. The only issue is the replacement gaskets don't seem to have any better stick or magnetic hold than the original gaskets, so I'm not sure the repair will improve the energy efficiency / performance of the appliance.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CAROLYN from SPARTANBURG, SC
- Parts Used:
- WPW10289497
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
refrigerator came with can/holder in door
i did not need the can holder in door, we do not buy can drinks. i would rather have the full shelf space, so i replaaced the can holder with a full shelf
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilynn from Holland, MI
- Parts Used:
- EDR4RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed to replace filter
Turned old one until it snapped out. Replaced it with a turn.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stanley from Gurley, AL
- Parts Used:
- W10827015
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Wife dropped a gallon of milk on the lid and cracked the see through panel
Pushed the hinge pins aside and removed the old lid.. Reversed the process to install the new lid
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Glendale, AZ
- Parts Used:
- WPW10326469, EDR4RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Center rail broke AGAIN
This is the 2nd time I had have had to replace the center rail in 2 years....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scot from Tijeras, NM
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Deli cover panel hinge pin broke off
Removed all of the bottom drawers and shelvs, then removed the end panel that contained the broken Deli cover hinge pin. Replaced with new panel, cleaned all of the existing parts and ten re-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rodger from Marion, IL
- Parts Used:
- W10874836
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Lid to chef pantry would not work.
First I removed the drawers and shelf above the pantry drawer and then removed the pantry drawer. The end cap came off very simply by removing two screws. I removed the slide attachment to the old end cap and attached it two the new end cap. I then installed the new end cap and replaced the drawers and shelf. The lid to the chef pantry popped right in place. Job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from San Diego, CA
- Parts Used:
- WP67006704
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper Glass Shattered While Cleaning
Since it was apparent the crisper glass is fragile I was very careful to not stress it. I opened the box then took a large board almost as big and slid it on. I carried both items to the fridge and with both doors open slid the glass into place. I am 65 yrs. Old and have owned many refrigerators but this is a first. They don't build them like they use to. .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Shreveport, LA
- Parts Used:
- W11368721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door was not closing with any positive feel and would often pop open when left door was shut.
Popped out old gasket and popped in nwe one. This is where things get interersting, the new gasket
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.
Does work as well as the one I replaced. I think the maganet is not strong enough. If anyone has had the same problem please let me know. This model ( Maytag- French door ) has been a lemon.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Emilio from Clinton, MD
- Parts Used:
- W10874836
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
End cap pin broken
The end cap is a very easy job to remove. Removed the three screws that hold the end cap in place using a 1/4 drive socket. Removed sliding rail which is affix to end cap to be reused with new end cap. Installed new end cap with the three screws and your done very easy. What made the job possible was the ability to identify the part from the PartsSelect.com web site which has excellent parts identification catalog.
Was this instruction helpful to you?
Thank you for voting!