KRSC700HPS06 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from WARMINSTER, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from LOVELAND, OH
- Parts Used:
- W11123941
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch lever broke
Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sung-Su from BISMARCK, ND
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the Rocker Switch in Fridge side
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from COTTONDALE, FL
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old filter was overdue for replacement
ordered new filter, removed old filter from fridge, and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L. from NEW ULM, TX
- Parts Used:
- W10346771A, W10311524
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filters needed changing
Took the old ones out and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from HOUSTON, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker not making ice and dripping water
This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orlando from Bayonne, NJ
- Parts Used:
- WP2300868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one leaks on one side
Simply cut the water tube on both sides of connector and push in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from WOODWAY, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not making ice
First turn off the ice maker. Then there's four screws in the very back you remove pull out the cover. There's hex head 516 bolts maybe quarter inch that hold in the ice maker unplug the ice maker reverse process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neala from Tubac, AZ
- Parts Used:
- W11226500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights in freezer were dim
This is regarding the top light in the freezer, Small screwdriver inserted into tabs on the right side of light pops it right out. Unplug and remove light. Plug in new light, snap into place DONE. Be sure to remove plastic film
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WEST PALM BCH, FL
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker not making ice
Simple to replace. 6 screws out. Unplug connections... Plug back in, replace screws.
Unfortunately still not making ice. Will try fill valve replacement.
Unfortunately still not making ice. Will try fill valve replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from EDENTON, NC
- Parts Used:
- W10873791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
My ice maker would only freeze for a short while, after unplugging it for a few hours it would begin to make ice again only to stop after a few trays
The repair went great, however, I had someone to put the part in for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from BOULDER, CO
- Parts Used:
- W10873791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice cube tray had a loose part hanging down
Did my homework.
Consulted Utube
Bought the part
Installed
Consulted Utube
Bought the part
Installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MESQUITE, NV
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ice container bin cracked and had a hole in it.
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cliff from BELTON, MO
- Parts Used:
- WPW10341320
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Water was leaking from back of fridge
After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door.
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake
Was this instruction helpful to you?
Thank you for voting!