KRFF300EBS01 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- daryl from Palm Harbor, FL
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear wheel
I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Studio City, CA
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator needed neplacement water filter
Opened holder removed old filter and replaced with new filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from Freeland, MI
- Parts Used:
- WPW10475495
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Broken rear support wheel
remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Bath, ME
- Parts Used:
- W11396033
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Light in Freezer Compartment Out
Changed bulb, not the problem, had to remove switch to identify correct choice to order (3 pronged verus 2) after that it was easy beyond having to stand on my head to make the exchange. (N B before removing old switch it actually came back to life)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Tillamook, OR
- Parts Used:
- W11745278
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Hinge bracket between refrig and bottom freezer had broken. This is the part which keeps the door from opening too far.
After I did the prep work of removing the items inside the door the project took less than 15 minutes to get the repair job done. 1. Remove the door by taking off the top hinge cover on top of the door, remove the three screws with a socket wrench, remove the plastic gasket under the hinge, left door up and off the lower hinge pin 2. Place the new bracket on the freezer door hinge pin, flange side down 3. I had to place an extra spacer washer, which I had on hand, on top of the hinge bracket 4. Replace the door on the bottom hinge pin 5. My husband held the door in place as I reattached the top of the door with the plastic spacer and 3 screws I had removed 6. Replaced the plastic gasket and hinge cap on the top 7. With the door reattached, I removed the existing screw under the door directly below the new hinge bracket, lined up the hinge bracket to the screw hole and attached it in place. Much to my surprise and pleasure, the door swings perfectly, stopping where it should with the door shelves loaded! Thank you PartSelect for having a part that would work for my 16 year old refrigerator even though I had to add a washer shim to make the new part as thick as the original.
Was this instruction helpful to you?
Thank you for voting!