KRSC703HBS04 KitchenAid Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from LOVELAND, OH
- Parts Used:
- W11123941
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light switch lever broke
Unplug refrigerator.
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Pry switch out with putty knife
Remove two wires from switch
Attach wires to new switch
Push new switch into slot
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sung-Su from BISMARCK, ND
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the Rocker Switch in Fridge side
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from WARMINSTER, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Evelyne from LOS ANGELES, CA
- Parts Used:
- W10355588
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Refridge door Gasket needed replacememt
Unfortunately the replacement part did not work. The directions required that the older Gasket had to be removed before the new could be inserted. The original gasket was inserted into a groove on the door and also "glued" in some way to the door.
When an area on the side of the door was carefully pulled out it revealed that the new one was insufficient to replace the original.. It was substantially thinner and did not have the design that extended and went into the groove on the door. It needed to go in the slot of the same size and width. There was no such part and no way the new gasket would/could attach to the door.. There was no way to attach this new part. This meant that it wouldn't fit and successfully close the door.
When an area on the side of the door was carefully pulled out it revealed that the new one was insufficient to replace the original.. It was substantially thinner and did not have the design that extended and went into the groove on the door. It needed to go in the slot of the same size and width. There was no such part and no way the new gasket would/could attach to the door.. There was no way to attach this new part. This meant that it wouldn't fit and successfully close the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from HOUSTON, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker not making ice and dripping water
This is an easy fix. The hardest part was just determining which part to replace. But the Q&A's for the ice maker from this site steered me right. And their video on how to install was easy to follow. The only difference I found was my Whirlpool had only 2 electrical connectors instead of the 3 in the video. I finished the job in about 15 minutes so everything in my freezer stayed solidly frozen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gene from COTTONDALE, FL
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old filter was overdue for replacement
ordered new filter, removed old filter from fridge, and installed new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- L. from NEW ULM, TX
- Parts Used:
- W10346771A, W10311524
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Filters needed changing
Took the old ones out and replaced with the new ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Orlando from Bayonne, NJ
- Parts Used:
- WP2300868
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old one leaks on one side
Simply cut the water tube on both sides of connector and push in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jay from WOODWAY, TX
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Not making ice
First turn off the ice maker. Then there's four screws in the very back you remove pull out the cover. There's hex head 516 bolts maybe quarter inch that hold in the ice maker unplug the ice maker reverse process
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from WEST PALM BCH, FL
- Parts Used:
- W10873791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Icemaker not making ice
Simple to replace. 6 screws out. Unplug connections... Plug back in, replace screws.
Unfortunately still not making ice. Will try fill valve replacement.
Unfortunately still not making ice. Will try fill valve replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neala from Tubac, AZ
- Parts Used:
- W11226500
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lights in freezer were dim
This is regarding the top light in the freezer, Small screwdriver inserted into tabs on the right side of light pops it right out. Unplug and remove light. Plug in new light, snap into place DONE. Be sure to remove plastic film
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from EDENTON, NC
- Parts Used:
- W10873791
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
My ice maker would only freeze for a short while, after unplugging it for a few hours it would begin to make ice again only to stop after a few trays
The repair went great, however, I had someone to put the part in for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from BOULDER, CO
- Parts Used:
- W10873791
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Ice cube tray had a loose part hanging down
Did my homework.
Consulted Utube
Bought the part
Installed
Consulted Utube
Bought the part
Installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MESQUITE, NV
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
ice container bin cracked and had a hole in it.
Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.
Was this instruction helpful to you?
Thank you for voting!