KSSP42QFB05 KitchenAid Refrigerator - Instructions

Removed the ice maker. Used a small mirror (wife's make up mirror) to find the screws. Inspected and found most teflon coating missing. Ordered new ice maker and installed. Works perfect.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

The nozzle of the water dispenser broke. I ordered the part which arrived the next day. I did not use the white line, only the black. I turned the water off, then I removed the screw under the broken nozzle and cut off it off from the line. I took a new screw and cut off the top with pliers, then twisted half of a screw in the old line and inserted the other half in the new line and pulled the line from the bottom corner of the refrigerator and connected it to the white line under the grid. Screwed the new nozzle back to the lever, replaced the grid and turned water on.

1.removed 3 nut screws-2 on top &1 on bottom.
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in about 2-3 hours

Easy removal. Easy Plug and play install. Didn't even have to use the other wires. After install, put 4 oz of water into ice maker and wait....it didn't start making ice right away, but a couple hours later I heard the wonderful "ice dropping into the bin" sound. Worked great ever since.

Old ice maker was beyond repair.I replace it with a new one.Removal and installation about 30 min.It was nice to know that there was video on line if needed.The ice bin problem was in the crusher,cube feed area.It took me about 30min.to take it apart.And 40min. to put it back together.All part fit and is working prefect.I must say the feed screw has a reverse thread,this could be of help.PARTS SELECT, prices and service was very good.I give them 4 out of 4 stars

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.

remove decorattive trim around ice and whater dispenser area, Remeved 2 hex nuts holing ice dispenser are in place, one nut has a spring attatched to help the arm go back into position once the arm has been depressed. removed and replaced new arm, works good as new.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

I looked up the PartSelection website. Found the parts from the sketches of units and reviewed the videos on repairs. Then I ordered the parts, altho I ordered the complete unit, instead of the control block that said was problem 59% of time. Following instructions replaced the ice maker. Then took apart the auger in the basket and thought I had an incomplete part, but upon closer inspection forund out it was correct. My only problem was that there was no instructions on how to get the block off end of shaft. Tried to impact it off, but by accident found out it screwed off. Then final repair went fast. Parts came fast and overall VERY happy with parts and repairs. They are heavier than original parts so should last longer.

1. PUsh the Lock button so the water will not run.
2.Remove the screw holding the nozzle.
3. Remove the Grill
4. Disconnect the black water tube. Pull the female part of the union off the old tube and hold it for the new tube.
5. PUll it the tube out from the nozzle end.
6. Snake the new tube into the hole and shove it through until it comes out the door hinge port at the bottom of the door.
7. Continue pushing and pulling the tube until the nozzle is in position.
8.Test fit the new tube and cut a short piece off to fit properly.
9. Slide the female part of the union onto the new tube. Insert it onto the union and tighten.
10. Insert the screw that holds the nozzle in place and tighten.
11. Push the on unlock button and fill a glass with water.
12. Check for leaks. If no leaks reinstall the grill.
Job done.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair