KSSO36QMB03 KitchenAid Refrigerator - Instructions

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Bi-metal defrost thermostat tested bad, so replaced. To remove back freezer panel on this model, remove top left and right shelf pegs (use a screw driver). This will let back freezer panel slide up and out.

Control board, located in metal box above the inverter board had a bad 200uF electrolytic capacitor (bulging top) and 12v relay. Replaced all 5 electrolytic capacitors on the board and all 4 relays.

Works good.

Local service person missed the diagnosis and advised $10,000 new refrigerator. I looked and saw that the switch was deformed and had burn marks. Searched for switch online. Found site Ordered. Part arrived next day. 5 minute job to replace. No tools needed. Refrigerator works great. Thank you t!

I watched the video this site has on their website and I did exactly as the instructor did. I had my ice maker fixed in less than 30 minutes. I had watched the video prior to receiving my parts so I already had the prep work done. I had the parts removed that needed removing and all I did was slide the new ones into place. Use the parts chart on this site to make sure you get the right parts and use the video to uninstall/install your parts. Do exactly like the instructor says and you won't have any problems. It was as my school kids say, "easy peasy". Thanks!!!

Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.

Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.

took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.

It was great repaired the problem for under $60

Popped off the front panel(from bottom) removed two screws to remove old part and put everything on new panel. Put everything back in place all in less then 15 minutes.
Ordered parts Wednesday forenoon and received it Thursday morning. Very outstanding service!

Remove the old part with pliers and pulled out used water filter Installed replacement water filter on cap and installed in grill area below door Hooray !

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

On the bottom of the cover plate are two slots. Insert thin bladed screw driver and pry out gently. Remove electrical connection plate. Remove the old door by removing pin from spring and retaining bracket useing long nose pliers. Install new door kit making sure you use all the parts in the kit. The door buffer is different and the new kit does not require a heater.Install the electrical plate, ice shute and front cover.

Removed coupling screw and coupling and replaced with new coupling and screw. Check your shaft as well , I didn’t and had to order and wait on IT to arrive before I could complete the job.

Removed the drip tray under ice & water dispenser & removed 2 screws holding faceplate.
Unsnapped 2 microswitches that control ice dispenser & water dispenser.
Removed 2 screws holding control bracket, replaced with new one & reassembled.
Done!

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks